BONFIGLIOLI Vectron ACTIVE CUBE Series Скачать руководство пользователя страница 117

Страница: 117 / 200

13.7

Motion Control Override

The Motion Control Override Function can be used to transmit the motion profile via

serial communication (VABus or Modbus). Therefore in the User software VPlus for

Windows a motion profile can be used when a control is not finished programming

during commissioning. This function can also be used as a simulation mode.

The Function Motion Control Override do not support the following modes:

•

Interpolated Mode.

•

Cyclic Synchronous Position Mode

•

Cyclic Synchronous Velocity Mode

Parameter

Setting

No.

Description

Min.

Max.

Fact. sett.

1454 Override Modes Of Operation

Selection

1455 Override Target Position

-2

-1…2

-1 u

1456 Override Profile Velocity

-1…2

-1 u/s

1457 Override Acceleration

-1…2

-1 u/s²

1458 Override Deceleration

-1…2

-1 u/s²

1459 Override Target Velocity vl [rpm]

-32768…32767 rpm

-1 rpm

1460 Override Target Velocity pv [u/s]

-2

-1…2

-1 u/s

Based on the standard settings of the Motion Control Interface (Parameters

1292…1297) the following cross reference results between Override Parameters and

CANopen Objects:

1454

Override Modes Of Operation

0x6060

Modes of Operation

1455

Override Target Position

0x607A

Target Position

1456

Override Profile Velocity

0x6081

Profile Velocity

1457

Override Acceleration

0x6083

Profile Acceleration

1458

Override Deceleration

0x6084

Profile Deceleration

1459

Override Target Velocity vl [rpm]

0x6042

Target Velocity

1460

Override Target Velocity pv [u/s]

0x60FF

Target Velocity

The default setting “-1” in Parameters 1455…1460 and “0” in Parameter 1454

Over-

ride Modes of Operation

results, that the value of the Motion Control Interface links of

Parameters 1292…1297 are used. Settings deviating from the factory setting will re-

sult in the usage of the individual parameter. It is possible to set certain aspects of the

trajectory via the Override function and other values via the Motion Control Interface.

The target position “-1 u” cannot be used as target position, because 1455

Override

Target Position

= -1

deactivates the Override Function.

07/13

CM-EtherCAT

117

Содержание ACTIVE CUBE Series









































































































































































































Результаты поиска

Содержание ACTIVE CUBE Series

Отзывы:

Похожие инструкции для ACTIVE CUBE Series

Бренды по названию

Популярные бренды

BONFIGLIOLI Vectron ACTIVE CUBE Series, Руководство пользователя

Результаты поиска

Содержание ACTIVE CUBE Series

Отзывы:

Похожие инструкции для ACTIVE CUBE Series

Бренды по названию

Популярные бренды