1. Assemble the complete housing
unit (key #2) and the base
casting (key #3) by inserting the
Hex Head Bolts (key #014).
2. Attach the complete housing unit
and base casting to the board
(key #9) by inserting the 1/2"
carriage bolts (key #15) into the
bottom of the board. Place the
base casting and housing on top
of the board and carriage bolts
(be sure that neither edge of the
base casting is flush with the
edge of the board).
ASSEMBLY INSTRUCTIONS
3. Next place the 1/2" flat washer
(key #16) and 1/2" nut (key #17)
on the carriage bolt and then
tighten the 1/2" nut.
Bon Tool Co. Rebar Cutter/Bender is shipped in two packages.
Please check your boxes to make sure you have all the required pieces.
5. Insert the 54" steel
handle (key #8) into one
of the sockets on the
complete housing unit
(key #2) and your unit is
ready to use.
6. For easy storage of Bon’s
Rebar Cutter/Bender place
the steel bar into a socket
on the housing unit, and
pull the handle down until
it hits the board (key #9).
Move the handle clip
(key #5) over the end of
the 54" steel handle and
tighten the handle clip
down with the 1/4" wing
nuts (key #20).
IS12359 05/18
PAGE 1 OF 2
4. To attach the handle clip (key #5) to
the board line up the slots on the
handle clip with the holes in the
board. Insert the 1/4" carriage bolt
(key #18) from the bottom of the
board and through the handle clip.
Then place the 1/4" flat washer
(key #19) and 1/4" wing nut (key
#20) on the carriage bolt and
tighten the 1/4" wing nut.
See Bon parts list PL12359 for complete information on all parts.
PARTS LIST
Ref # Key # Part #
Detail
Qty/Unit
12-359
2
50-353
Housing w/ Grease Fitting
1
12-359
3
50-354
Base Casting
1
12-359
4
50-355
Back Plate
1
12-359
5
50-356
Handle Clip
1
12-359
6
50-357
Hub w/ Bushing
1
12-359
7
50-358
Beraring Set (48 pcs)
1
12-359
8
50-359
54" Steel Handle w/Grip
1
12-359
9
50-360
Mounting Board
1
12-359
10
52-661
Grease Fitting (not shown)
1
12-359
11
50-361
Roller Pin with Cotter Pin
1
12-359
12
50-362
Roller Pin w/Cotter
1
12-359
13
12-367
Cutter-Bushing Set (2 pcs)
2
12-359
14
52-479
Hex Head Bolt of Base
2
12-359
15
52-414
Carriage Bolt 1/2" x 2-1/2"
2
12-359
16
52-101
Flat Washer 1/2" on Base
2
12-359
17
52-199
Nut 1/2"
2
12-359
18
52-413
Carriage Bolt 1/4" x 2-1/4"
2
12-359
19
52-100
Flat Washer 1/4"
2
12-359
20
52-260
Wing Nut 1/4"
2
12-359
21
52-490
Hex Head Bolt Set for Hub
7
12-359
22
51-113
Handle Grip
1
12-359
23
52-143
Lock Washer 1/2"
2
12-359
24
52-666
Grease Cap
1
12-359
25
52-422
Hex Head Bolt M8 x 1.25 X 30mm
1
12-359
26
805-80375 Spacer
1
Bon Tool Co. • 4430 Gibsonia Rd. • Gibsonia, PA 15044 • USA • www.bontool.com
#
12-359 Rebar Cutter/Bender
