Bompani 96A, Инструкция по эксплуатации и техническому обслуживанию

Страница: 25 / 76

25
-.press.gently.on.the.upper.side.of.the.glass.so.that.the.three.pins,.
with.silicone.on.the.inside,.fit.into.their.holes..
-.make.sure.that.the.door.closes.completely.
CONNECTING TO THE GAS SUPPLY
Before.connecting.the.cooker,.check.that.it.is.preset.for.the.gas.to.be.
used..Otherwise,.make.the.conversion.as.described.in.the.section.
headed."Adapting.to.different.gas.types"...The.connection.is.on.the.
right;.if.the.pipe.has.to.pass.behind.the.cooker,.it.must.be.kept.low.
down.where.the.temperature.is.about.50.degrees.C.
-.Rigid.connection.(see.Fig..5,.diagram.D):
. The.connection.to.the.mains.gas.supply.may.be.made.using.a.rigid.
metal.pipe.(D)...Remove.the.hose.connector.and.screw.the.rigid.
union.onto.the.threaded.connection.of.the.gas.train..The.union.for.
rigid.connection.is.amongst.the.cooker.accessories.
-.Connection.using.a.rubber.hose.(see.Fig..5,.diagrams.B.and.C):
. Connect.a.rubber.hose.carrying.the.conformity.mark.currently.in.
force.to.the.hose.connector..The.hose.must.be.replaced.at.the.date.
indicated,.and.must.be.secured.at.both.ends.using.standard.hose.
clamps..It.must.be.absolutely.accessible.to.allow.its.condition.to.
be.checked.along.its.entire.length.
-.Connection.using.a.metal.hose.(see.Fig..5,.diagram.D):
. Make.the.connection.using.a.hose.which.complies.with.national.
standards,.screwing.it.onto.the.connector.with.a.ring.seal,.which.is.
delivered.amongst.the.cooker.accessories.
-.After.installation,.check.that.all.connections.are.airtight.
-.For.operation.with.butane/propane,.check.that.the.gas.pressure.is.
as.indicated.on.the.nameplate.
IMPORTANT:
-.Use. only. standard. rubber. hoses.. . For. LPG,. use. a. hose. which.
complies.with.the.national.regulations.in.force.
-.Avoid.sharp.bends.in.the.pipe.and.keep.it.well.away.from.hot.sur-
faces.
References.to.the.regulations.covering.the.gas.connection.to.the.
appliance:.ISO.7-1.
ADAPTING TO DIFFERENT TYPES OF GAS
If.the.cooker.is.not.already.preset.to.operate.with.the.type.of.gas.
available,.it.must.be.converted...Proceed.as.follows:
-.Replace.the.injectors.(.table.on.page.22);
-.regulate.the.primary.air.flow;
-.regulate.the.minimum.settings.
N.B.:.every.time.you.change.the.type.of.gas,.indicate.the.new.type.
of.gas.on.the.serial.number.label.
REPLACING THE HOB BURNER INJECTORS (fig. 6)
-.Remove.the.grid,.the.burner.caps.(A),..and.the.burners.(B);
-.unscrew.and.remove.the.injector.in.the.bottom.of.each.injector.
holder.(C);
-.replace.the.injector.in.accordance.with.the.table.in.page.22,..using.
a.7.mm.socket.wrench,.tighten.and.screw.right.down;
-.check.that.the.system.is.gas-tight;
-.replace.the.burners,.the.burner.caps.and.the.grid;
IMPORTANT:
-.Never.over-tighten.the.injectors;
-.after.replacing,.check.that.all.the.injectors.are.airtight.
REPLACING THE OVEN BURNER INJECTOR (fig. 7a)
-.Loose.the.screw.securing.the.oven.bottom;
-.remove.the.oven.bottom.(push.back.and.raise);
-.remove.the.oven.burner,.after.taking.out.its.fixing.screw;
-.replace.the.injector,.using.a.7.mm.socket.wrench.
REPLACING THE GRILL BURNER INJECTOR (fig. 7b)
-.Remove.the.burner.after.taking.out.the.two.screws.which.secure.
it;
-.replace.the.injector.using.a.7.mm.socket.wrench.
IMPORTANT:
-.Never.over-tighten.the.injectors;
-.after.replacing,.check.that.all.the.injectors.are.airtight.
SETTING HOB BURNER MINIMUM LEVELS
If.the.cooker.is.to.work.on.bottled.gas.(butane/propane),.the.tap.
by-pass.must.be.screwed.right.down.The.cooker.may.be.equipped.
with.type.A.taps,.with.by-pass.inside.(accessed.by.inserting.a.small.
screwdriver.into.the.rod).or.type.B.taps,.with.by-pass.on.the.outside.
on.the.right.(accessed.directly)...See.figure.8.
If.the.cooker.is.to.work.on.natural.gas,.proceed.as.follows.for.both.
types.of.tap:
-.Ignite.the.burner.at.maximum.flame;
-.pull.off.the.knob,.without.using.a.lever.against.the.control.panel,.
which.might.be.damaged;
-.access.the.by-pass.with.a.small.screwdriver.and.back.off.by.about.
3.turns.(turning.the.screwdriver.anti-clockwise);
-.turn.the.tap.rod.anti-clockwise.again.until.it.stops:.the.burner.will.
be.at.maximum.flame;
-.screw.the.by-pass.slowly.back.in,.without.pushing.the.screw-driver,.
until.the.flame.has.apparently.shrunk.to.1/4.of.the.maximum.size,.
checking.that.it.is.sufficiently.stable.even.in.quite.strong.draughts.
SETTING OVEN BURNER MINIMUM LEVELS
If.the.cooker.is.to.work.on.bottled.gas.(butane/propane),.the.ther-
mostat.by-pass.must.be.screwed.right.down.If.the.cooker.is.to.work.
on.natural.gas,.proceed.as.follows:
-.Remove.the.oven.bottom.(push.towards.the.back.and.raise);
-.ignite.the.oven.burner,.turning.the.knob.pointer.to.the.maximum.
setting;
-.shut.the.oven.door;
-.access.the.thermostat.by-pass.(.fig..9);
-.back.off.the.thermostat.by-pass.by.about.3.turns;
-.after.5.or.6.minutes,.turn.the.knob.pointer.to.the.minimum.setting;.
-.slowly.re-tighten.the.by-pass,.watching.the.flame.decrease.in.size.
through.the.window.in.the.closed.oven.door.until.the.tongue.of.the.
flame.is.about.4.mm.long...Never.keep.the.flame.too.low...It.must.
be.stable.even.when.the.oven.door.is.opened.or.closed.quickly;
-.turn.off.the.burner.and.replace.the.oven.bottom.
CONNECTING TO THE ELECTRICAL MAINS
Before.making.the.connection,.check.that:
-.the.mains.voltage.is.as.indicated.on.the.nameplate;
-.the.earth.connection.is.in.good.working.order.
If.the.appliance.power.lead.is.not.fitted.with.a.plug,.use.an.approved.
standard.type,.remembering.that:
-.the.green-yellow.wire.must.be.used.for.the.earth.connection;
-.the.blue.wire.is.the.neutral;
-.the.brown.wire.is.live;
-.the.lead.must.never.touch.hot.surfaces.over.about.75.degrees.C;
-.replacement.leads.must.be.of.type.HO5RR-F...of.suitable.size.(see.
diagrams.in.fig..2).
-.if.the.appliance.is.supplied.without.lead,.using.type.HO5RR-F...cable.
of.suitable.size.(see.diagrams.in.fig..2).
IMPORTANT:.the.manufacturer.declines.all.liability.for.damage.due.to.
failure.to.comply.with.the.regulations.and.standards.in.force...Check.
that.the.appliance.is.correctly.connected.to.the.earth.(see.diagrams.
in.fig..2.at.the.back.of.the.manual).
FOR COOKERS WITH ELECTRIC IGNITION
The.correct.gaps.between.the.electrode.and.the.burner.are.shown.
in.figures.7a,7b.
If.no.spark.is.generated,.do.not.keep.on.trying.as.this.might.damage.
the.generator.
Possible.causes.of.malfunctions:
-.spark.plug.damp,.dirty.or.broken;
-.electrode-burner.gap.not.correct;
Installation
GB