Bompani 66 N Series, Инструкция по эксплуатации и техническому обслуживанию

Страница: 18 / 40

18
GB
Technical data and specifications
GAS BURNERS (injectors and flow-rates)
Nominal external dimensions Cookers
60x60
Height at hob
Height with lid raised
Depth with door closed
Depth with door open
Width cm. 86,5
cm. 143
cm. 60
cm. 104
cm. 60
Usable dimensions 60x60
static oven
60x60
fan oven
Width
Depth
Height
Volume cm. 45
cm. 47
cm. 34
l. 72 cm. 41
cm. 38
cm. 31
l. 50
Gas Burner Injector low
flow-rate
(kW)
nominal
flow-rate
(kW)
G20
20
mbar
auxiliary
semi-rapid
rapid
oven
grill
ultra-rapid ec.
TC Ecoring
77
97
123
130
99
145
107
0,40
0,58
0,80
1,00
-
1,70
1,6
1,00
1,65
2,80
3,00
1,85
4,00
3,8
G30
28-30
mbar
G31
37
mbar
auxiliary
semi-rapid
rapid
oven
grill
ultra-rapid ec.
TC Ecoring
50
65
83
86
68
98
69
0,40
0,58
0,80
1,00
-
1,70
1,6
1,00
1,65
2,80
3,00
1,85
4,00
3,5
G110
8
mbar
auxiliary
semi-rapid
rapid
oven
grill
ultra-rapid ec.
TC Ecoring
150
185
265
300
200
350
220
0,40
0,58
0,80
1,00
-
1,70
1,6
1,00
1,65
2,80
3,00
1,85
4,00
3,5
Cat.: seename plate on cover; Class 1 or 2.1
Type “X” cookers
ELECTRIC HOTPLATES
ø 145
1,2 kW - High-Light hotplate
ø 180
1,5 kW - Normal hotplate
1,8 kW - High-Light hotplate
2,0 kW - Rapid hotplate
ø 210 -120 2,1 - 0,7 kW - High-Light hotplate
ø 265 -170 2,2 - 1,4 kW - High-Light hotplate
HEATING ELEMENT POWERS
bottom element 1.1 kW
top-bottom element 1.1 - 1.5 kW
circular element
2,0 kW
grill 2,0 kW
oven light 40 W
roaster motor 5 W
IMPORTANT:
The manufacturer declines all liability for damage due
to failure to comply with the regulations and standards
in force. Check that the appliance is correctly con-
nected to the earth (see diagrams in fig. 2 at the back
of the manual).
FOR COOKERS WITH ELECTRIC IGNITION
The correct gaps between the electrode and the burner
are shown in figures 5a,5b.
If no spark is generated, do not keep on trying as this
might damage the generator.
Possible causes of malfunctions:
- spark plug damp, dirty or broken;
- electrode-burner gap not correct;
- spark plug wire broken or without sheathing;
- spark discharging to earth (to other parts of the
cooker);
- generator or microswitch damaged;
- air has built up in the pipes (particularly if the cooker
has been out of use for a long time);
- air-gas mixture incorrect (poor fuel setting).
THE SAFETY DEVICE
The correct gap between the end of the thermocouple
sensor and the burner is shown in figures 5a,5b.
To check that the valve is working properly, proceed
as follows:
- ignite the burner and leave it to work for about 3 min-
utes;
- turn off the burner by returning the knob to off position
( );
- after 90 seconds for hob burners, 60 seconds for oven
and grill burners, turn the knob pointer to the "on"
position;
- release the knob in this position and move a burning
match towards the burner; IT MUST NOT IGNITE.
Time needed to excite the magnet during ignition: 10
seconds approx.
Automatic tripping time, after flame has been turned off:
not more than 90 seconds for hob burners; not more
than 60 seconds for oven and grill burners.
IMPORTANT:
- Before doing any work inside the cooker, disconnect
the mains plug and shut the gas tap.
- Never use matches to check the gas circuit for leaks.
If a specific control device is not available, foam or
very soapy water can be used.
- When re-closing the hob, check that the electrical
wires of the spark plugs (if present) are not close to
the injectors, so that they cannot run across them.
Warning Installation