Bolin Technology DANTE AV D Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 47

Bolin Technology DANTE AV D Series Скачать руководство пользователя страница 18

18

The Rx Utilization includes not only network traffic destined for the Dante device, but any other
multicast or broadcast traffic received at this network interface.

Note:

As a rule of thumb neither the Rx nor the Tx utilization should exceed about 85% of the link speed

to guarantee good clock synchronization performance (links are full duplex).

The graphic also indicates the speed and connected state of the interface as follows:

Indicates that the link is operating at 1Gbps

Indicates that the link is operating at 100Mbps

Indicates that the link is not connected, or that
there is an error. The IP address will read N/A, and
Tx and Rx utilization will be 0 kbps.

Clear Counters

: Click this button to reset the packet errors history for the device.

Latency Tab

Status Tab with Bolin Dante AV camera

Note:

For video (Dante AV) devices, latency settings made in Dante Controller apply only to the audio channels.

Status Tab with Bolin Dante AV decoder

«
...
16
17
18
19
20
...
»

Содержание DANTE AV D Series
















































Отзывы:

Нет отзывов