Bolin Technology BC-9 Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 57

Bolin Technology BC-9 Series Скачать руководство пользователя страница 47

47

Upgrading MCU Firmware

MCU Firmware can be upgraded by following these steps:

1. Load the .bin file onto a flash drive (Formatted as FAT32), and

name the file “HD20.bin”

2. With the camera powered off, insert the flash drive to the USB

port on the back panel of the camera

3. Apply power to the camera

The green indicator light above beside of the lens will turn red for a
few seconds while the upgrade takes place. Once the upgrade is
finished, the light will turn off. The camera will proceed through a
normal boot cycle. Check the Fw version information on the OSD boot
screen to confirm the new FW has been upgraded.

Upgrading IP encoder firmware

You can upgrade camera IP encoder module Firmware via IP network.
Connect and configure your camera with your local network successfully, log in the camera IP web interface,
go to System, Maintenance section to upgrade the firmware.
How to make Firmware upgrade for IP Encoder, please refer to User Manual Part Two.

Upgrading FPGA firmware

You can upgrade camera FPGA Firmware via IP network.
Connect and configure your camera with your local network successfully, log in the camera IP web interface,
go to System, Maintenance section to upgrade the firmware.
How to make Firmware upgrade for FPGA, please refer to User Manual Part Two.

Video Resolution Upgrade

If you bought the camera that is FHD version, now you decide to upgrade it to 4K version. We can make it for
you. This firmware upgrade gives you following features added to the camera that you bought:

1. The camera you have bought is FHD resolution and 3G-SDI output.
2. By purchasing a upgrade license, you can have following features added to the camera:

a.  Resolution will be upgrade to 4K, 2160p30/23.98
b.  SDI video output will be upgraded to 6G-SDI.
c.  Other features may be upgraded.
d.  This license upgrade feature is only applied to following models:

i. License BC-7-4K20S-LS-4K for BC-7-4K20S-S3MNB PTZ camera

ii. License BC-9-4K12S-LS-4K for BC-9-4K12S-S3MN PTZ camera

How to upgrade your camera from FHD to 4K:

The FHD-4K upgrade license is for being purchased

.

1. Please contact your local dealer where you bought the camera from or Bolin technical support team

for help with purchasing the upgrade license.

2. Get the MAC Address from OSD menu of the camera that you want to upgrade and provide it to Bolin

tech-team via your seller.

3. A FPGA firmware with license included will be provided to you. This FPGA firmware is tied to the

camera MAC address that only workable to the camera that you are asking upgrading for.

4. The FHD-To-4K license upgrade firmware can be

installed to the camera via IP network.

5. Connect and configure your camera with your local

network successfully. Go into the camera OSD
menu, locate the Network Menu showing MAC
Address, stay with the menu shown.

6. Login to the camera IP web interface, go to

System, Maintenance section to upgrade the
firmware.

7. How to make Firmware upgrade for FPGA, please

refer to User Manual Part Two.

EXPOSURE
WHITE BALANCE

DETAIL
PICTURE
GAMMA

>NETWORK
PAN TILT ZOOM

>

SYSTEM

OSD

IPv4

192.168.002.234

SUBNET MASK 255.255.255.0

GATEWAY 192.168.002.001

MAC ADDRESS 00:26:C2:01:02:EE

NETWORK MENU

«
...
45
46
47
48
49
...
»

Содержание BC-9 Series


























































Отзывы:

Нет отзывов