background image

S2000-К

41

www.bolid.com

User’s Code
Entered

ECOD      80     D007

A user has presented to a reader of the device with
the network address 7 the authenticator #80 regis-
tered by the network controller

Local User’s
Code Entered

ECOD    405(l) D001

A user has presented to a reader of the device with
the network address #1 the authenticator #405 regis-
tered by the device itself

Device Tamper
Alarm

TA         D001

The enclosure of the device with the network address
1 has been open

Device Tamper
Restored

TR         D001

The enclosure of the device with the network address
1 has been closed

Device
Connected

CONNECT  D018

The network controller has found the device with the
address 18 within the connected RS-485 interface bus

Device
Disconnected

DISCONNECT  D018

Communication between the network controller and
the device with the network number 18 has been lost:
or the device has been replaced

Device Restarted

RESTART   D018

The device with the network address 18 has been re-
started

Power Failure

PWRF  D018

The input voltage of the device with the network ad-
dress 18 is out of the normal range

Access
Granted

AG        41   D001

The device with the network address 41 has made a
decision to grant access via its protected door to  a
user having presented the authenticator #41

Access Denied

AD         41   D001

The authenticator #41 has been read by a reader of
the device with the network address 1, the authentica-
tor being not authorized to gain access to the opera-
tion requested

Illegal Code

ICOD         D001

An unknown authenticator has been presented to a
reader of the device with the network address 1

Door Forced Open

DRF           D001

The door monitored by the device with the network
address 1 has just been open without granting access

Door Held Open

DRO          D001

The door monitored by the device with the network
address 1 has been open for more than a specified
time

Door Closed

DRC          D001

The door monitored by the device with the network
address 1 has just been closed after being held open
or forced open

Local
Programming

PROGR    D001

The device with the network address 1 has entered
the Key Programming Mode

Содержание S2000-K



















































Отзывы: