background image

 

 

 

BodyGuard 

SAFETY SOLUTIONS 

-Tag 

®

 

 

Driver Awareness System

 

  

 

BodyGuard Safety Solutions—A division of Orbit Communications Pty Ltd          Install Guide rev r1.11        

Page 

17

 

Alarm Activation 

A Tag detected within the detection zone of a sensor unit causes an audible alarm to sound, followed 
by a human voice indication of the risk. 

For a single sensor system “Look Out! Person near you”. For dual sensor system “Look out! Person in 
front of you” or “Look Out! Person behind you”. The high brightness LEDs on the front panel (in the 
shape of a STOP sign) will begin to flash. The siren will repeat approximately every 5 seconds while 
the Tag remains in the detection zone, and the LEDs will continue to flash. 

When the Tag leaves the detection zone, the LEDs will stop flashing and siren will cease. The alarm 
takes around 1 second to stop after Tag leaves the zone. 

Mute 

If the driver presses the mute switch while an alarm is active, a voice will advise “Speaker Muted” and 
the repeating siren will cease. The LEDs will remain flashing as long as the Tag is still in the detection 
zone.  If  the  Tag  leaves  the  zone  OR  another  Tag  enters,  then  the  alarm  resets  and  starts  again 
automatically. The driver cannot permanently mute the speaker. 

Driver Tag Lockout 

The Driver Tag Lockout is a feature that enables the driver to wear a Tag without activating his or her 
own vehicle alarm. 

Two methods are available: 

1.

 

Press and hold MUTE button longer than 3 seconds, while alarm is active. The driver Tag must 
be  only  tag  in  detection  zone.  This  method  works  ok  for  intermittent  use  but  not 
recommended for long-term use due to higher battery consumption. Use Rechargeable Tags 
for long-term use. The Driver Tag will UNLOCK automatically when the vehicle is switched off, 
ensuring the Tag cannot permanently lock out. 

2.

 

Tag “Disable Pouch”. This pouch mounts to the vehicle. Tags disable while in the pouch and 
automatically enable when removed. The driver places the Tag into pouch when operating 
the vehicle and then removes the Tag when leaving the vehicle. 

    

 

Driver Tag “Disable Pouch”

Содержание i-Tag





















Отзывы: