manualshive.com logo in svg

Bobrick AirCraft B-701, Руководство по устранению неисправностей и информации, Страница: 41 / 66

Поделиться
Скачать
Bobrick AirCraft B-701 Скачать руководство пользователя страница 41

Page 8 

 

      

 

 

Warning 

Risk of electric 

shock 

Disconnect power 

supply before 

removing cover 

Instructions For The Replacement Of The B-710 Series A 

CompacDryer

TM

 Cover 

 

 

 

 

 

To Remove Existing Cover 

1.  Remove  the  (3)  Phillips-head 

screws  from  the  cover,  (1)  from  each 

side  and  (1)  from  the  bottom  face  of 
the dryer. See Fig. 1. 

2.  Pull  the  bottom  of  the  cover 
outward  and  slightly  downward,  then 

rotate  upward  to  disengage  the(2) 

tabs  from  the  slots  at  the  base.  See 
Fig. 2. 

To Install New Cover 

1.  Slide cover onto base plate making 

sure  that  the  bottom  outlet  aperture 

engages  in  the  sides  of  the  outlet 
grille. 

2.  Push  the  top  of  the  cover  forward 
until the (2) tabs snap into the slots in 

the base. See Fig. 3. 

3.  Check  that  the  cover  is  a  close  fit 
to  the  base,  then  replace  the  (3) 

screws. 
4.  Reconnect  electrical  supply  and 

test  with  normal  hand  drying 
procedure, allowing 10 seconds for the 

sensor to stabilize. 

Fig 1

 

Fig 2

 

Fig 3

 

Содержание AirCraft B-701



































































Отзывы:

Нет отзывов