4.
Insert a new type CR 2032 battery with the
positive side facing upwards.
5.
Press the cover back into position.
Dispose of old batteries at a Service
Partner of the manufacturer or another
qualified Service Partner or a specialist
workshop or hand them into an authorised col‐
lecting point.
Additional remote controls
Additional remote controls are available from a
Service Partner of the manufacturer or another
qualified Service Partner or a specialist work‐
shop.
Loss of remote controls
A lost remote control can be blocked and re‐
placed by a Service Partner of the manufacturer
or another qualified Service Partner or a special‐
ist workshop.
If a driver profile, see page
, has been as‐
signed to the lost remote control, the connection
to this remote control must be removed. A new
remote control can then be assigned to the
driver profile.
Malfunction
General
A Check Control message, see page
shown.
It may be difficult for the vehicle to detect the re‐
mote control in some conditions, including the
following:
▷
The battery of the remote control is dis‐
charged. Replacing the battery, see page
▷
Disruption of the radio link by transmission
masts or other equipment transmitting pow‐
erful signals.
▷
Shielding of the remote control by metallic
objects.
Do not transport the remote control together
with metallic objects.
▷
Disruption of the radio link by mobile tele‐
phones or other electronic devices in the im‐
mediate vicinity of the remote control.
Do not transport the remote control together
with electronic devices.
▷
Interference with radio transmission caused
by the charging of mobile devices, for exam‐
ple a mobile phone.
▷
The remote control is located in the immedi‐
ate vicinity of the wireless charging dock.
Place the remote control somewhere else.
If there is a malfunction, the vehicle can be un‐
locked and locked from the outside with the
integrated key, see page
.
Switching on drive-ready state via
the remote control special ID feature
The drive-ready state cannot be switched on if
the remote control has not been detected.
If this happens, proceed as follows:
1.
Hold the back of the remote control against
the mark on the steering column. Pay atten‐
tion to the display in the instrument cluster.
2.
If the remote control is detected:
Switch on drive-ready state within 10 sec‐
onds.
If the remote control is not detected, change the
position of the remote control slightly and repeat
the procedure.
Seite 79
Opening and closing
CONTROLS
79
Online Edition for Part no. xxx - X/18
Содержание Z4 Roadster
