BMW S 1000R 2015 страница 63 Скачать руководство пользователя

Страница: 63 / 207

Mirrors

Adjusting mirrors

Turn the mirror to the desired
position.

Front and rear seats

Removing rear seat

Make sure the ground is level
and firm and place the motor-
cycle on its stand.

Open seat lock

with the igni-

tion key.
Lift the rear seat at the rear
and then work it back and up
to remove.
Remove the ignition key from
the lock and place the rear
seat, upholstered side down,
on a clean surface.

Install the rear seat

Engage the rear seat in
mounts

on left and right.

Swing the rear seat down,
pushing it lightly forward.

Operation

ProCarManuals.com

Содержание S 1000R 2015
















































































































































































































Результаты поиска

Содержание S 1000R 2015

Отзывы:

Похожие инструкции для S 1000R 2015

Бренды по названию

Популярные бренды

BMW S 1000R 2015, Руководство пользователя для мотоциклиста

Результаты поиска

Содержание S 1000R 2015

Отзывы:

Похожие инструкции для S 1000R 2015

Бренды по названию

Популярные бренды