BMW S 1000R 2015 Скачать руководство пользователя страница 61

Страница: 61 / 207

Do not turn the handlebars or
the handlebar fitting on the
handlebar.

WARNING

Adjusting the brake lever
while riding.

Risk of accident

Do not attempt to adjust the
brake lever unless the motor-
cycle is at a standstill.

Turn knob

to the desired po-

sition.

NOTICE

The adjuster is easier to turn
if you push the brake lever
forward.

Adjustment options:
Position 1: largest span
between handlebar grip and
brake lever
Position 6: smallest span
between handlebar grip and
brake lever

Tyres

Checking tyre pressure

WARNING

Incorrect tyre pressure.

Impairment of the motorcycle's
handling characteristics. Shorter
useful tyre life.

Always check that the tyre
pressures are correct.

WARNING

Tendency of valve inserts to
open by themselves at high
riding speeds.

Sudden loss of tyre pressure.

Install valve caps fitted with
rubber sealing rings and tighten
firmly.
Make sure the ground is level
and firm and place the motor-
cycle on its stand.
Check tyre pressures against
the data below.

Tyre pressure, front

2.5 bar (Tyre cold)

Tyre pressure, rear

2.9 bar (Tyre cold)

Operation

ProCarManuals.com

Содержание S 1000R 2015
















































































































































































































Результаты поиска

Содержание S 1000R 2015

Отзывы:

BMW S 1000R 2015, Руководство пользователя для мотоциклиста, Страница: 61 / 207

Результаты поиска

Содержание S 1000R 2015

Отзывы: