manualshive.com logo in svg

BMW S 1000R 2015, Руководство пользователя для мотоциклиста

Поделиться
Скачать
BMW S 1000R 2015 Скачать руководство пользователя страница 32

EWS active

General warning light shows
yellow.

EWS!

appears on the display.

Possible cause:
The key being used is not au-
thorised for starting, or commu-
nication between key and engine
electronics is disrupted.

Remove all other vehicle keys
from the same ring as the igni-
tion key.
Use the reserve key.
Have the defective key re-
placed, preferably by an au-
thorised BMW Motorrad dealer.

Coolant temperature too
high

General warning light
flashes red.

The coolant-temperature reading
flashes.

ATTENTION

Riding with overheated en-
gine.

Engine damage

Compliance with the
information set out below is
essential.

Possible cause:
The coolant temperature is too
high.

If possible, ride in the part-load
range to cool down the engine.
Check the coolant level.
If the coolant temperature
is frequently too high, have
the fault rectified as soon
as possible by a specialist
workshop, preferably an
authorised BMW Motorrad
dealer.

Engine in emergency-
operation mode

Warning light for engine
electronics shows.

WARNING

Unusual ride characterist-
ics when engine running in
emergency-operation mode.

Risk of accident

Adapt your style of riding ac-
cordingly.
Avoid accelerating sharply and
overtaking.

Possible cause:
The engine control unit has dia-
gnosed a fault. In exceptional
cases, the engine stops and re-
fuses to start. Otherwise, the en-
gine runs in emergency operating
mode.

You can continue to ride, but
bear in mind that the usual en-
gine power or the full range of

3

30

z

Status indicators

ProCarManuals.com

Содержание S 1000R 2015
















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды