background image

© BMW AG, München 

01 29 0 406 372

 12.2005 (Z/Z)

Original BMW Accessory.

Installation Instructions.

1

Advanced DVD system with multimedia changer retrofit

BMW 7 Series Saloon (E 65 / E 66)

Retrofit kit No.

65 12 0 406 359

DVD advanced monitors installation kit

65 12 0 406 362

DVD advanced MMC installation kit

Installation time

The installation time for the full system (multimedia changer and two rear monitors) is approx. 5.0 hours. 
If you only install one rear monitor and the multimedia changer, the installation time will be 
approx. 4.0 hours. The installation time may vary depending on condition of the car and the equipment 
in it.

Important information 

These installation instructions are primarily designed for use within the BMW dealership organisation 
and by authorised BMW service companies.

In any event the target group for these installation instructions is specialist personnel trained on BMW 
cars with the appropriate specialist knowledge.

All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals 
and work instructions in a rational order using the prescribed tools (special tools) and observing current 
health and safety regulations.

To avoid unnecessary extra work and/or costs, if any installation or function problems occur, 
after a brief troubleshooting session (approx. 0.5 hours), contact the following:
1. Either your national sales company or your regional office or 
2. The Support team via the Aftersales Assistance Portal (ASAP) using the optional technical 

parts support application.

Quote the VIN and the part number of the retrofit kit and provide a detailed description of the 
problem.

Do not archive the hard copy of these installation instructions since daily updates are made by ASAP.

See ASAP for details of the pictograms.

All the figures show LHD cars, proceed in exactly the same way on RHD cars.

Pictograms

s

Denotes instructions that draw your attention to special features.

Denotes the end of the instruction or other text.

Subject to technical modifications.

Содержание 65 12 0 406 359































Отзывы: