103
The corresponding memory button
1
is now
programmed with the signal of the original
hand-held transmitter.
You can operate the device while the ignition is
switched on.
If the device fails to function even after
repeated programming, check whether
the original hand-held transmitter uses an alter-
nating-code system. To do so, either read the
instructions for the original hand-held transmit-
ter or hold down the programmed memory
button
1
of the integrated universal remote
control. If the LED
2
on the integrated universal
remote control flashes rapidly and then remains
lit for about two seconds, the original hand-held
transmitter uses an alternating-code system. If
it uses an alternating-code system, program
the memory buttons
1
as described under
Alternating-code hand-held transmitters.
<
Alternating-code hand-held
transmitters
To program the integrated universal remote
control, consult the operating instructions for
the device to be set. You will find information
there on the possibilities for synchronization.
When programming hand-held transmitters
that employ an alternating code, please observe
the following supplementary instructions:
Programming will be easier with the aid of
a second person.
<
1.
Park your vehicle within the range of the
remote-controlled device.
2.
Program the integrated universal remote
control as described above in the section
Fixed-code hand-held transmitters.
3.
Locate the button on the receiver of the
device to be set, e.g. on the drive unit.
4.
Press the button on the receiver of the
device to be set. After step 4, you have
approx. 30 seconds for step 5.
5.
Press the programmed memory button
1
of
the integrated universal remote control
three times.
The corresponding memory button
1
is now
programmed with the signal of the original
hand-held transmitter.
If you have any questions, please contact
your BMW center.
<
Deleting all stored programs
Press the left and right memory buttons
1
for
approx. 20 seconds until the LED
2
flashes rap-
idly: all stored programs are deleted.
Reassigning individual programs
1.
Hold the original hand-held transmitter at a
distance of approx. 4 to 12 in/10 to 30 cm
from the memory buttons
1
.
The required distance between the
hand-held transmitter and the mem-
ory buttons
1
depends on the system of the
respective original hand-held transmitter
used.
<
2.
Press the desired memory button
1
of the
integrated universal remote control.
3.
If the LED
2
flashes slowly after approx.
20 seconds, press the transmit key of the
original hand-held transmitter. Release
both buttons as soon as the LED
2
flashes
rapidly. If the LED
2
does not flash rapidly
after approx. 15 seconds, alter the distance
and repeat this step.
Online Edition for Part no. 01 41 2 603 066 - © 08/09 BMW AG
Online Edition for Part no. 01 41 2 603 066 - © 08/09 BMW AG
Содержание 2010 323i
