101
Practical interior accessories
Integrated universal remote
control*
The concept
The integrated universal remote control can
replace as many as three hand-held transmit-
ters for various remote-controlled devices,
such as garage doors and gates or lighting sys-
tems. The integrated universal remote control
registers and stores signals from the original
hand-held transmitters.
The signal of an original hand-held transmitter
can be programmed on one of the three mem-
ory buttons
1
. After this, the programmed
memory button
1
will operate the system in
question. The LED
2
flashes to confirm trans-
mission of the signal.
Should you sell your vehicle one day, be sure to
delete the stored programs beforehand for your
safety, refer to page
To prevent possible damage or injury,
before programming or using the inte-
grated universal remote control, always inspect
the immediate area to make certain that no peo-
ple, animals or objects are within the pivoting or
travel range of the device being operated. Com-
ply also with the safety instructions supplied
with the original hand-held transmitter.
<
Checking compatibility
If this symbol appears on the package
or in the instructions supplied with the
original hand-held transmitter, you can
assume that the radio remote control device will
be compatible with the integrated universal
remote control.
For additional information, please contact your
BMW center or call: 1-800-355-3515.
You can also obtain information on the Internet
at:
www.bmwusa.com or
www.homelink.com.
HomeLink is a registered trademark of Johnson
Controls, Inc.
<
Programming
1
Memory buttons
2
LED
Fixed-code hand-held transmitters
1.
Switch on the ignition, refer to page
2.
When starting operation for the first time:
Press the left and right memory buttons
1
for approx. 20 seconds until the LED
2
flashes rapidly. The three memory buttons
are cleared.
3.
Hold the original hand-held transmitter at a
distance of approx. 4 to 12 in/10 to 30 cm
from the memory buttons
1
.
The required distance between the
hand-held transmitter and the mem-
ory buttons
1
depends on the system of the
respective original hand-held transmitter
used.
<
4.
Simultaneously press the transmit key on
the original hand-held transmitter and the
desired memory button
1
on the integrated
universal remote control. The LED
2
flashes
slowly at first. As soon as the LED
2
flashes
rapidly, release both buttons. If the LED
2
does not flash rapidly after approx. 15 sec-
onds, alter the distance and repeat this
step.
5.
To program other original hand-held trans-
mitters, repeat steps 3 and 4.
ba8_E9293M3_cic.book Seite 101 Dienstag, 19. August 2008 12:01 12
Online Edition for Part no. 01 41 2 600 999 - © 08/08 BMW AG
Содержание 2009 M3
