113
Practical interior equipment
Integrated universal remote
control*
Principle
The integrated universal remote control
replaces up to three different hand-held trans-
mitters for various systems or devices that are
operated by radio remote control, for example a
garage door, a driveway gate or domestic alarm
systems. The integrated universal remote con-
trol identifies and learns the signals transmitted
by the original hand-held transmitters.
The signal from an original hand-held transmit-
ter can be programmed to one of the three
memory buttons
1
. The memory button
1
that
has been programmed in this way can then be
used to operate the relevant device when the
ignition is switched on. Transmission of the sig-
nal is shown by the LED
2
.
If and when you decide to sell your car, in the
interests of security clear the programmed
functions first, see page
114
.
During the programming operation and
before a programmed system is operated
with the integrated universal remote control,
make sure that no persons, animals or objects
are within the pivoting or movement range of
the system in question, otherwise there is a risk
of injury or damage. Comply also with the safety
instructions supplied with the original hand-
held transmitter.
<
Checking compatibility
If this symbol appears on the pack or in
the instructions supplied with the origi-
nal hand-held transmitter, you can
assume that the radio remote control device will
be compatible with the integrated universal
remote control.
A list of compatible hand-held transmitters can
be found on the website www.homelink.com.
You can also call the freephone HomeLink hot-
line at +49 (0)6838 907 277, or
0800 0466 35465 from within Germany.
HomeLink is a registered trademark of Johnson
Controls, Inc.
Programming
1
Memory buttons
2
LED
Fixed-code hand-held transmitter
1.
Switch on the ignition, see page
2.
When using for the first time: press the left
and right memory buttons
1
for approx.
20 seconds until LED
2
flashes rapidly. All
memorised programs are deleted.
3.
Point the original hand-held transmitter at
memory buttons
1
at a distance of approx.
10 to 30 cm, approx. 4 to 12 in.
The required distance between the
hand-held transmitter and memory
buttons
1
depends on the system accord-
ing to which the original hand-held trans-
mitter operates.
<
4.
Press the command button on the original
hand-held transmitter and the desired
memory button
1
on the integrated univer-
sal remote control at the same time. The
LED
2
initially flashes slowly. When the
LED
2
starts to flash rapidly, release both
buttons. If LED
2
does not start to flash rap-
idly after approx. 15 seconds, change the
distance and repeat the process.
Online Edition for Part-No. 01 41 0 013 209 - © 04/07 BMW AG
Содержание 2007 X5 3.0d
