BlueSun 10 A Скачать руководство пользователя страница 1

MPPT Solar Controller

Characteristics

MPPT series controller is  suitable for the street light

system. The controller features a smart tracking algorithm

inside that maximizes the energy from the solar PV

module(s) and charge the battery. At the same time, the

low voltage disconnect function (LVD) will prevent the

battery from over discharging.

The controller charging process has been optimized for

long battery life and improved system performance. The

comprehensive self-diagnostics and electronic protection

functions can prevent damage from installation mistakes

or system faults.

Peak conversion efficiency of 97 %, high Tracking

efficiency of 99%.

Very fast sweeping of the entire I-V curve, several

seconds tracking speed.

Widely used, automatic recognize day/night.

Timer function with 1-15 hours option for street light.

Unique dual timer function, enhance the flexibility of

street light system.

Sealed, Gel and Flooded battery option.

Adopting temperature compensation and correcting the

charging and discharging parameters automatically,

improving the battery lifetime.

Electronic protection: over charging, over discharging,

overload, short circuit.

Reverse protection: any combination of solar module

and battery, without causing damage to any component.

RJ45 interface with remote meter MT-5, convenient to

check operating parameters of controllers. ( MT-5 is

optional)

1

PLURIGÁS SOLAR ENERGIAS Lda. - End: Urb. António Aleixo -1 , 4820-358 Fafe, Portugal

Tel : +351 253700060 - Fax : +351 253700065 – Site: www.plugassolar.pt – Email: [email protected]

Содержание 10 A











Отзывы: