Blue Summit BG952UHV Скачать руководство пользователя

Страница: 55 / 56

507266-04B

Page 55 of 56

Issue 1904

Planned Service

A service technician should check the following items

during an annual inspection. Power to the unit must be

shut off for safety.

Fresh air grilles and louvers

(on the unit and in the

room where the furnace is installed) - Must be open and

unobstructed to provide combustion air.

Burners

- Must be inspected for rust, dirt, or signs of water.

Vent pipe

- Must be inspected for signs of water, cracked,

damaged or sagging pipe, or disconnected joints.

Unit appearance

- Must be inspected for rust, dirt, signs of

water, burnt or damaged wires, or components.

Blower access door

- Must be properly in place and

provide a seal between the return air and the room where

the furnace is installed.

Return air duct

- Must be properly attached and provide

an air seal to the unit.

Operating performance

- Unit must be observed during

operation to monitor proper performance of the unit and

the vent system.

Combustion gases

- Flue products should be analyzed

and compared to the unit specifications.

Problems detected during the inspection may make it

necessary to temporarily shut down the furnace until the

items can be repaired or replaced.

Instruct the homeowners to pay attention to their

furnace.

Situations can arise between annual furnace

inspections that may result in unsafe operation. For

instance, items innocently stored next to the furnace may

obstruct the combustion air supply. This could cause

incomplete combustion and the production of carbon

monoxide gas.

Repair Parts List

The following repair parts are available through Blue

Summit dealers. When ordering parts, include the complete

furnace model number listed on the CSA nameplate. All

service must be performed by a licensed professional

installer (or equivalent), service agency, or gas supplier.

Cabinet Parts

•

Upper Access Panel

•

Blower Access Panel

• Top Cap

Control Panel Parts

• Transformer
•

Integrated Control Board

•

Door Interlock Switch

Blower Parts

•

Blower Wheel

•

Motor

•

Motor Mounting Frame

•

Motor Choke

•

Blower Housing Cutoff Plate

Heating Parts

•

Flame Sensor

•

Heat Exchanger Assembly

•

Gas Manifold

•

Combustion Air Inducer

•

Gas Valve

•

Main Burner Cluster

•

Main Burner Orifices

•

Pressure Switch

•

Ignitor

•

Primary Limit Control

•

Flame Rollout Switches

Содержание BG952UHV

























































Результаты поиска

Содержание BG952UHV

Отзывы:

Похожие инструкции для BG952UHV

Бренды по названию

Популярные бренды

Blue Summit BG952UHV, Руководство по установке

Результаты поиска

Содержание BG952UHV

Отзывы:

Похожие инструкции для BG952UHV

Бренды по названию

Популярные бренды