background image

© Copyright 2012 Prizer –Painter Stoves Works   

        “REV 1 – 6/14/2012”

 

INSTALLATION, USE AND CARE MANUAL 

FOR PROFESSIONAL VENTILLATION FOR 

THE HOME 

 

IMPORTANT!—PLEASE READ AND FOLLOW 

1.  THIS APPLIANCE WAS DESIGNED FOR EASE OF INSTALLATION AND OPERATION.  HOWEVER, WE 

RECOMMEND THAT YOU READ ALL SECTIONS OF THIS MANUAL BEFORE YOU BEGIN INSTALLA-
TION.  

2.  DO NOT REMOVE PERMANANTLY AFFIXED LABELS, WARNINGS OR DATA PLATES FROM YOUR 

APPLIANCE.  THIS MAY VOID THE MANUFACTURER’S WARRANTY AND/OR HINDER EFFECTIVE 
SERVICING AND MAINTENANCE. 

3.  THESE INSTRUCTIONS ARE TO REMAIN WITH THE APPLIANCE AND THE CONSUMER IS TO RE-

TAIN THEM FOR FUTURE REFERENCE. 

4.  PLEASE OBSERVE ALL LOCAL AND NATIONAL BUILDING CODES AND ORDINANCES.  IF NO LO-

CAL CODES ARE APPLICABLE, PLEASE FOLLOW ALL WIRING REQUIREMENTS IN ACCORDANCE 
WITH THE NATIONAL ELECTRICAL CODE, ANSI/NFPA 70 EDITION. 

5.  PLEASE CHECK WITH A QUALIFIED AND TRAINED INSTALLER OR YOUR LOCAL CODES FOR ANY 

MAKE UP AIR REQUIREMENTS. 

6.  THIS HOOD IS FOR RESIDENTIAL USE ONLY AND IS NOT DESIGNED FOR INSTALLATION OVER A 

COMMERCIAL PRODUCT.   

7.  MAKE SURE ALL POWER IS TURNED OFF AT THE MAIN BREAKER OR FUSE BOX BEFORE MAKING 

ANY CONNECTIONS. 

8.  TO AVOID RISK OF FIRE , ELECTRIC SHOCK, OR INJURY TO PERSONS, TURN OFF THE ELECTRIC-

ITY TO THE HOOD FROM THE POWER SUPPLY BEFORE CLEANING OR SERVICING.  

This product is intended for domestic use only! 

                                   P/N 750306 Page   1 

Содержание BS-PL30240





































Отзывы: