background image

Blue Sky Energy 

 Solar Boost 3000i 

 

15

                                                                                                                                                                                                       Blue Sky Energy | USA | 

www.blueskyenergyinc.com

 

Specifications:

 

SB3000i @12V 

Maximum PV Power:

 

400W with 36-cell PV panel

(*)

 

290W with 60-cell PV panel

(*)

 

Rated Battery (Output) Current:

 

30A with 36-cell PV panel

(*)

 

 22A with 60-cell PV panel

(*)

 

Conversion Efficiency:

 

97% (typical @28V / 24A output) 

Power Consumption:

 

0.36W (typical standby) 

Recommended Max Panel Voc at STC:

 

40V (Max Panel Input 50V)  

Charge Profile:

 

Multi-Stage plus Manual or Automatic Equalization  

Absorption Voltage:

 

14.4V

(1)

 

 

Float Voltage:

 

13.2V

(1)

  

 

Equalization Voltage (if enabled):

 

15.2V

(1)

  

 

Auxliary Output (option A, B, or C):

 

A) Auxiliary Battery Charge 2A (2nd battery) 

B) Load Control 

C) Dusk-to-Dawn

 

and PWM dimming

(1)

  

 

Load (LVD) Disconnect/Reconnect Voltage:

 

11.5V/12.6 V

(1)

  

 

Maximum Auxiliary Output current (option B or C):

 

20A 

Display:

 

Yes 

Temperature Compensation (by optional Battery Temp. Sensor):

 

-5.00mV/°C/cell correct factor (Range 0.00 to -8.00mV/°C/cell)

(1)

  

 

Operating Temperature:

 

-40°C 

 45°C 

Maximum Full Power Ambient:

 

45°C 

Environmental Protection:

 

IP20 

Weight:

 

1.08 lb. (493 g) 

Dimensions:

 

6.35 x 4.6 x 2.2" (16.1 x 11.7 x 5.6 cm) 

(*)

 

36-

cell panels are typically referred to as “12V panels” providing Vmp/Voc of ~18V/22V at STC, 60

-cell panels refers to "20V panels" (Vmp/Voc ~30V/37V), 72-cell 

panels refers to "24V panels" (Vmp/Voc  ~36V/44V)  -  

 

(1)

  

Factory default, programmable via digital display. 

NB. As a part of our continuous improvement process specifications are subject to change without prior notice. 

 

FIVE YEAR LIMITED WARRANTY 

Blue Sky Energy, Inc. (hereinafter BSE), hereby warrants to the original consumer purchaser, that the product or any part thereof shall be free from 
defects due to defective workmanship or materials for a period of five (5) years subject to the conditions set forth below.  
 
1. 

This limited warranty is extended to the original consumer purchaser of the product, and is not extended to any other party. 

2. 

The limited warranty period commences on the date the product is sold to the original consumer purchaser. A copy of the original purchase 
receipt identifying purchaser and date of purchase, must accompany the product to obtain warranty repairs.  

3. 

This limited warranty does not apply to, and future warranty shall become void, for any product or part thereof damaged by; a) alteration, 
disassembly or application of a foreign substance, b) repair or service not rendered by a BSE authorized repair facility, c) accident or abuse, d) 
corrosion, e) lightning or other act of God, f) operation or installation contrary to instructions pertaining to the product, or g) cosmetic aging. 

4. 

If BSE’s examination of the product determines that the product is not defective the consumer shall be charged a test and eva

luation fee of 

$30 and be responsible for all transportation costs and insurance related to returning the product to the consumer. The consumer is ultimately 

responsible for proper installation and operation of the product and BSE’s prior troubleshooting assistance shall not serve a

s a waiver of the 

test and evaluation fee. The test and evaluation fee is subject to change without prior notice. 

5. 

If  within  the  coverage  of  this  limited  warranty,  BSE  shall  repair  or  replace  the  product  at  BSE’s  sole  discretion  and  return 

the  product  via 

standard ground transportation of BSE’s choosing within the continental US.

 The consumer shall be responsible for all transportation costs and 

insurance to return the product outside the continental US, and for all transportation costs and insurance related to expedited return of the 

product. BSE’s liability for any defective pro

duct or any part thereof shall be limited to the repair or replacement of the product. BSE shall not 

be liable for any loss or damage to person or property, or any other damages, whether incidental, consequential or otherwise, caused by any 
defect in the product or any part thereof.  

6. 

Any implied warranty for merchantability or fitness for a particular purpose is limited in duration to the length of this warranty.  

7. 

To  obtain  warranty  repairs,  contact  BSE  at  760-597-1642  or  [email protected]  to  obtain  a  Returned  Goods Authorization 
(RGA) number. Mark the outside of the package with the RGA number and return the product, postage prepaid and insured to the  address 
below. The consumer is responsible for all transportation costs and insurance related to returning the product to BSE, and for any shipping 
damage which may void the warranty or increase the cost of repairs. 

 
 

Содержание SB3000i

















Отзывы: