Blue Sea Systems 7521 (25A) Скачать руководство пользователя страница 1

Read and understand the contents of this User Manual. It contains important safety, handling, and operational instructions for the P12 Battery Chargers.
This User Manual describes the product mentioned herein at the time of its publication. Specifications and performance are subject to change at the discretion 
of Blue Sea Systems. To view the most current revision of this publication visit bluesea.com/P12.

Scan for 
additional
product
information

P12

User Manual

7521 

(25A)

 and 

7522 

(40A)

BATTERY CHARGER

12V DC

CHARGING

ALERT

C H A R G I N G   S T A G E

EQUALIZE – ALL LIGHTS FLASH

FLOAT

ABSORB

BULK

PREFLOAT

www.bluesea.com

Patent Pending

P12

QuickGuide

BATTERY CHARGER

N° article  

 7521  7522

Courant maximum de sortie totale  

 25A  40A

Tension de sortie nominale             

   12V CC

Raccordements de sortie 

   3 positifs

 

   1 négatif

Tension d'entrée CA

 universelle   

   90–265V CA

Fréquence d'entrée CA

 nominale  

   45–65 Hz

Tension de sortie maxi.  

   16,0V CC

Précision de tension de sortie      

   0.05V CC

Température de fonctionnement mini.   

-20°C (-4°F) 

Température de fonctionnement maxi.  

 70°C (158°F)

Température de stockage mini.       

  -30°C (-22°F) 

Température de stockage maxi.        

   80°C (176°F) 

Courant parasite maxi.           

   2mA    

    

 Regulatory

Design and construction compliance to UL-1236 

marine (including ignition protection) and CSA

  22.2 

No. 107.2-0 standards. Meets all elements of the 

ABYC A-31 and certain NMEA

 requirements

. To view 

the most current regulatory certifications, 

visit www.bluesea.com/P12.

Part Number 

 7521  7522

Total Output Current (Limited) 

 25A  40A

Nominal Output V

oltage 

 12V DC

Output Connections 

 3 positive

 

 1 negative

 Universal AC Input V

oltage 

 90–265V AC

Nominal AC Input Frequency 

 45–65 Hz

Maximum Output V

oltage 

 16.0V DC

Output Voltage 

Accuracy  

 0.05V DC

Minimum Operating 

Temperature 

-20°C (-4°F)

    

Maximum Operating 

Temperature 

 70°C (158°F)

Minimum Storage 

Temperature 

-30°C (-22°F) 

Maximum Storage 

Temperature 

 80°C (176°F) 

Maximum Parasitic Current 

 2mA    

    

 

DESIGN

ED 

ASSEMB

LED

and TEST

ED

in the 

USA

Содержание 7521 (25A)

































Отзывы: