Blue Coat ProxySG SG900-10 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 104

background image

96

ProxySG 900 Series Maintenance & Upgrade Guide

Slide Rail Kit

2-Post Mid Mount Rail Assembly

The mid mount installation requires two Rail_B brackets to be installed onto the equipment
rack (per side). The Rail_B brackets support the appliance, while the front bracket (Rail_A)
secures the appliance.

To install the mounting brackets onto the equipment rail:

1.

Install two Rail_B mounting brackets onto the equipment rail.



Note:

The rack screws used in this step are not included with the slide rail kit as they are

rack-specific. See your equipment rack installation guide for more information on screw
sizing.

a.

Install the front Rail_B bracket with the mounting surface facing towards the rear
using (2) rack screws. Do not fully tighten! The Rail_B bracket will be tightened after
the appliance is secured into the rack.

b.

Install the rear Rail_B bracket with the mounting surface facing towards the front
using (2) rack screws. Do not fully tighten! The Rail_B bracket will be tightened after
the appliance is secured in the rack.

c.

Repeat for the other side. Verify the Rail_B mounting brackets are at the same height
in the rack

«
...
94
95
96
97
98
...
»

Содержание ProxySG SG900-10









































































































Отзывы:

Нет отзывов

Похожие инструкции для ProxySG SG900-10

Бренд: Brocade Communications Systems Страницы: 106

Бренд: Sonnet Страницы: 6

ZyXEL Prestige 310

Бренд: ZyXEL Communications Страницы: 199

SUPERSTACK 3CR16110-95

Бренд: 3Com Страницы: 4

Бренд: Lundix It Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды