Blue Coat ProxySG SG900-10 Скачать руководство пользователя страница 29

Страница: 29 / 104

ProxySG 900 Series Maintenance & Upgrade Guide

Fan Assembly

This section describes how to replace a fan assembly in the ProxySG 900 Series appliance.

The ProxySG 900 Series appliance contains seven identical serviceable fan assemblies that
maintain the ideal temperature for the system components - two power supply fan units (one
for each PSU inlet) and five system fan units.



Note:

The fan assemblies are hot-swappable; you can remove and replace a faulty fan

assembly while the appliance remains powered on.

The fan assemblies are numbered from left to right as indicated in the diagram. Each fan
assembly consists of two counter-rotating fan units.

Pre-Installation Checklist

Item

Description

Tools Required

None

Components Supplied

Fan assembly

Other Required Components

None

Safety Notices

●

See “Safety Warnings and Cautions” on page 8.

●

Put on an electrostatic discharge (ESD) strap before opening the appliance.

Содержание ProxySG SG900-10









































































































Результаты поиска

Содержание ProxySG SG900-10

Отзывы:

Похожие инструкции для ProxySG SG900-10

Бренды по названию

Популярные бренды

Blue Coat ProxySG SG900-10, Руководство по обслуживанию и модернизации

Результаты поиска

Содержание ProxySG SG900-10

Отзывы:

Похожие инструкции для ProxySG SG900-10

Бренды по названию

Популярные бренды