background image

4

FOCN

Instruction Manual

Forward Optical Receivers
RF Output

Frequency Range (+/- 1.0 dB): 54-1000 MHz (NTSC) 
Output Level (@ -1 dBm optical input):

*

   +28 dBmV (@ 550 MHz)
Return Loss: 14 dB min., 16 dB typical
Impedance: 75 Ohm
CNR (@ 0 dBm optical input):

*

  > 53 dB

CSO (@ -1 dBm optical input):

*

  > 63 dBc

CTB (@ -1 dBm optical input):

*

  > 65 dBc

Slope:  0dB
RF Test Point (forward) -20 dB; Type F

Optical

Wavelength: 1280 - 1610 nm
Optical Input Power Range: +2 dBm to -8 dBm
Return Loss: > 50 dB with APC connector
Optical Input Power Test Point: 
   1 V/mW +/- 0.1 V
Optical Connector: SC/APC, 8° APC

 

*  NOTE: Typical levels @ 0 dB slope to 1000 MHz with 8dBm 

optical transmitter with OMI @ 3.2%, & 77 NTSC channel 

loading to 550 MHz & digital loading to 1000 MHz (-6 dB 

below analog).

Electrical & Mechanical

Dimensions: 3” H x 6” D x 2.1” H
Weight:  12 oz.
Operating Temperature Range: 
   -10 to +55˚C (temperature at the mounting plate)
Enclosure IP Rating: IP20
Powering: +12 VDC  
  (via external Power Supply (included))
DC Ripple: < 50 mV
Power Dissipation (with return TX): < 7 W

Return Optical Transmitters 

Specifications 

F-P & DFB Versions RF Input

Frequency Range: (+/- 1.0 dB) 5-42 MHz (NTSC)
RF Test Point (return): -20 dB (external); Type F
Return Loss (with Return TX Installed): 
   > 16 dB within the Return Band
Return Path NPR: 15 dB min. of NPR Range  
  FP: 37 dB NPR Threshold 
  DFB: 41 dB NPR Threshold

Optical

Optical Output: 
  DFB = 4.8dBm (3mW) @1310nm 
  DFB = 4.0dBm (2.5mW) @1550nm
Return Loss: > 50 dB with APC connector
Optical Connector SC/APC, 8° APC

Содержание FOCN Series













Отзывы: