background image

Industry Canada statement:  

This device complies with ISED’s license-exempt RSSs. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation.  

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de 
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas 
produire  de  brouillage  préjudiciable,  et  (2)  ce  dispositif  doit  accepter  tout  brouillage  reçu,  y 
compris un brouillage susceptible de provoquer un fonctionnement indésirable.  

Radiation Exposure Statement: 

This  equipment  complies  with  ISED  radiation  exposure  limits  set  forth  for  an  uncontrolled 
environment.  This  equipment  should  be  installed  and  operated  with  greater  than  20cm 
between the radiator & your body.  

Déclaration d'exposition aux radiations: 

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un 
environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm entre 
le radiateur et votre corps. 

WARNING: RISK OF ELECTRIC SHOCK 

Basic  precautions  should  always  be  followed  when  using  electrical  products, 
including the following: 

Read all the instructions before using this product.

This device should be supervised when used around children.

Do not put fingers into the EV connector.

Do not uses this product if the flexible power cord or EV cable is frayed, has
broken insulation, or any other signs of damage.

Do  not  use  this  product  if  the  enclosure  or  the  EV  connector  is  broken,
cracked, open, or shows any other indication of damage.

To avoid a risk of fire or electric shock, do not use this unit with an extension
cord.

WARNING: RISK OF ELECTRIC SHOCK 
Improper connection of the equipment grounding conductor can result in a risk of 
electric shock. Check with a qualified electrician or serviceman if you are in doubt 
as to whether the product is properly grounded. 
Do not modify the plug provided with the product – if it will not fit the outlet, have a 
proper outlet installed by a qualified electrician. 

Basic/Smart/Intelligent Charger-32A

 Installation Manual Rev. 4.0 

BlinkCharging.com • (888) 998.2546

©2021 Blink Charging Co. • NASDAQ: BLNK

I

I

I

 

Содержание Basic Charger-32A























Отзывы: