background image

Repair and Maintenance Clause 

Only licensed electricians can repair or maintain the charge point. It is forbidden for general
users to repair or maintain it.

Turn off input power before repair or maintenance the charge point.

Federal Communication Commission Interference Statement 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation.  

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and 
can

 

radiate  radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the 

instructions, may cause harmful  interference to radio  communications. However, there is no 
guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does 
cause harmful interference to radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct the interference by one of 
the following measures:  

- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate this equipment.  

This transmitter must not be co-located or operating in conjunction with any other antenna or 
transmitter.  

Radiation Exposure Statement: 

This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an  uncontrolled 
environment.  This  equipment  should  be  installed  and  operated  with  greater  than  20cm 
between the radiator & your body. 

Basic/Smart/Intelligent Charger-32A

 Installation Manual Rev. 4.0 

BlinkCharging.com • (888) 998.2546

©2021 Blink Charging Co. • NASDAQ: BLNK

I

I

 

Содержание Basic Charger-32A























Отзывы: