switch
box
D
v1
intelligent dual switch devices
in μWiFi technology
Do not connect loads with a power greater than the permissible
one.
Connect in accordance with the scheme presented in the manual.
Incorrect connection can be dangerous, it can
result in damage to the controller and loss of warranty.
DANGER! Danger to life due to electric current (also with the de-
vice off), voltage may be present at the outputs. All assembly work
should be carried out ALWAYS with the circuit disconnected
power.
Connecting the device to the power grid without the quality re
-
quirements specified in the standard
PN-EN 50160 results in the loss of warranty.
1
INSTALLATION - BASICS
SAFETY RULES
CONNECTION DIAGRAM
CONTROL DEVICES FROM ANYWHERE IN THE WORLD
Before installing the controller, disconnect the voltage in the powered circuit.
Remember that all assembly work should be performed with the power supply
disconnected (switching off the mains fuse or disconnecting the power cord from
the socket).
The controller should be mounted in a place protected against unfavorable envi
-
ronmental conditions, protected against access by third parties - in a flush-moun
-
ted box or inside the housing of the controlled device. Remember that metal ele
-
ments (cables, housing parts) negatively affect the range of the device, and thus
the comfort of use.It is advisable that the device be fixed in a stable and stationary
position.Due to the operating voltage of the device, it is necessary that the con
-
nectors in the controller are protected against accidental touching or short circuits
that may result in electric shock or damage to the device.
Familiarize yourself with the scheme and then proceed to the installation of the
controller. Pay particular attention to the labeling of the controller connectors.
Start by connecting the power wires - phase L (brown) and neutral N (blue).Then
connect the load. If you decide to use local control from a wall switch, also
connect the switch as shown in the diagram. For control via smartphone or
tablet only, no wall switch is required.
The controller supports all types of monostable double switches (so-ca
-
lled bell switches). The sequence of connecting the S1 / S2 input to
the right / left switch button does not matter at the installation sta
-
ge – it can be set at a later stage of the controller configuration.
After making sure that the device has been connected in accordance with
the diagram and that there are no metal elements near the controller that
could accidentally short-circuit the contacts, turn on the device by swit
-
ching on the power supply (switching on the mains installation fuse or con
-
necting the power cord to a socket).
FIRST START
2
Unlock your phone or tablet and download the
free wBox application
.
If
you have an Android device, the application can be found in the Play store.
For iOS devices, the application is available in the App Store. The Windows
Phone app can be downloaded from the Windows Phone Store.
Using a mobile phone or tablet, connect to the device’s wireless network.
To do this, enter the settings of your smartphone or tablet, then to the
configuration of the WiFi network and find the network called “switch
-
BoxD-xxxxxxxxxx ” where xxxxxxxxxx is the serial number of the device.
Connect with this one network.
Turn on the wBox application. You will see your device at the top of the
screen. To add it to the application, click “+” on the right side, next to
the name. To preliminarily configure the driver, click on the default device
name.
Test the operation of the controller by clicking the ON / OFF button,
paying attention to connected load behaviour. If you connected a wall
switch, check its operation. In the default configuration for monostable
buttons (so-called bell buttons), holding the button key should turn on the
load, releasing the button will turn the load off. To change this behaviour,
go to settings (button “Settings” in the upper right corner of the screen)
and then in the option “set actions for input”, for the corresponding action
(you can set up a maximum of 10 actions
for the button) select the appropriate action type for the given trigger. For
example, to alternately turn the light on / off with the monostable button
each time it is pressed, select the action type as “change state” and select
“short press” as the trigger.
Also, check the selection in the “state after reboot” which determines the
method behaviour of the controller after a restart caused by e.g. a break in
the supply of electricity. You can choose if the load should stay on, off, stay
in the pre-reboot state (if it was on it should remain turned on, if it was
turned off, it must remain turned off), or take the opposite.
You can also configure it using the phone/tablet web
browser. After connecting with the wireless network of
the controller, turn on the browser and go to the websi
-
te: http://192.168.4.1
user manual
ACCESS POINT AND WIFI
NETWORK SETTINGS
3
After the first start-up of the controller, you can proceed to its further
configuration. Being connected to the WiFi network emitted by the
device, on the control panel of the wBox application, select the device,
then go to settings (the “Settings” button in the upper right corner of the
screen).
You can change the name of the device under which it is displayed in the
application wBox. In addition, you can change the name and password of
N
L
switch
Box
D
230V AC 2x4A max
de
vic
e 1
de
vic
e 2