background image

15

DEUTSCH

ENGLISH

FRANÇAIS

IT

ALIANO

NEDERLANDS

SVENSKA

ESP

AÑOL

PORTUGUÊS

TROUBLE SHOOTING GUIDE

FINAL SYSTEM CHECK

1.  No power

2.  “Flickering”: The electronic crossover

power indicator switches on and off re-
peatedly when the audio system is on.

3. The electronic crossover heats up

quickly even when the audio system is
at moderate volume.

SYMPTOM

PROBALE CAUSE

TROUBLE SHOOTING GUIDE

Check all the ground, B+ and remote
control terminals for tight connection.

Check all fuses.

Use a Volt/Ohm meter to check all cur-
rent carrying cables to see if the sys-
tem is rec12V.

Check whether the electronic crossover
B+ power input is connected directly to
the battery.

Check the battery voltage: if low, re-
charge or replace it.

Check whether the electronic crossover
has a good ground connection
(i.e.whether the ground wire is making
good contact with a bare spot of the ve-
hicle chassis.).

Check that all ground connections of
the entire system are making good
contact with bare metal.

Check for speaker short: circuit discon-
nect speaker cable from amplifier. Test
speaker with a Volt/Ohm meter. If there
is a short circuit in the speaker wiring,

Содержание Velocity VEX-01













Отзывы: