Wireless Thermostatic Radiator Valve (TRV-S1)
P
P
a
a
r
r
t
t
s
s
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
1. Valve Cap
2. LCD Screen
A.
ON:
Device is learnt in and wirelessly connected with
panel.
OFF:
Device is either not learnt in, or has lost
connection with panel.
B.
Low Battery Indicator
C.
On: Device set to default night temperature 17 °C.
Flash: Valve closing
On: Device set to default day temperature 21 °C.
Flash: Valve opening.
D. Auto / Manual mode
E. Boost mode indicator
F. Open Window
G. Setpoint / Status Indication
InS:
When device is powered on.
AdA:
Device motor working
F1/F3:
Valve Jammed
F2:
Device not installed on valve.
3. Function Buttons
-
Auto/Manual: Toggle between Auto and Manual mode.
-
Boost: Speed up heating
-
: Toggle between default Day / Night temperature.
4
.
Temperature Sensor / Status Indication
5. Control Knob
Turn to adjust temperature.
6. Battery Compartment
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
1 x Radiator Valve
2 x 1.5V AA Alkaline batteries.
1. Remove the battery cover to insert batteries.
2. The device will power on. The LCD screen will display
“
InS
”
and flash icon. The valve will turn to full open.
3. Refer to your Control Panel manual to put panel into learning
mode.
4. Press and hold the central
“
Boost
”
button for about 10
seconds and release when the LCD screen displays
“
888
”
Wait a few seconds.
5. Refer to panel manual to complete the learning process.
6. Wait for the icon to stop flashing, then install the device
onto the pipe, turn the valve nut to tighten.
7. Press the Auto/Manual button, the LCD will display
“
AdA
” and
icon will flash. The valve will turn to full close.
8. Wait for the valve to finish turning and complete installation.
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
A
A
d
d
j
j
u
u
s
s
t
t
m
m
e
e
n
n
t
t
Toggle between Auto and Manual mode by pressing the
Auto/Manual button.
Manual Control
Turn the knob at bottom of device to control temperature setpoint.
between 5
°
C to 30
°
C. Setting temperature to over 30
°
C will set
the device to ON. Setting temperature below 5
°
C will set the
device to OFF.
ON:
When turned to ON, the valve will be opened completely
after 1 minute. This function is used to preserver battery life
during summer, when heating is not required. Do NOT use this
function in winter when heater is activated, otherwise the room
temperature will rise without control.
OFF:
When turn to OFF, the valve will be closed completely after
1 minute. This function is used when heater is activated but
heating is not required in a room with no occupants.
Remote Control
Use the Home Automation function Blaupunkt Home Connect
server or Secure4Home smartphone application to adjust
temperature setpoint. You can also program Schedule setting via
remote control function:
Schedule Setting: Up to 5 schedules can be programmed for
every weekday with Mode, Setpoint and Start time.
Schedule Control:
Normal - The Radiator Valve will execute programmed schedule
setting accordingly.
No Schedule
– The Radiator Valve will not execute any set
schedule until it is set to Normal again.
B
B
o
o
o
o
s
s
t
t
B
B
u
u
t
t
t
t
o
o
n
n
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
&
&
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
