background image

www.blaubergventilatoren.de

SHM 100 DK

5

38

163

171

153

103

250 – 420

ø103

TECHNICAL DATA

The temperature in the room where the indoor unit of the ventilator is installed must be in the range from +5 °C to + 40 °C with relative 
humidity up to 65 % (no condensation build-up). If the conditions of using the ventilator exceed the specified limits, ensure the flow of 
fresh air through the windows.
The solar battery should be installed in a place with the maximum intensity of sunlight, for example, on the south side of the building. 
Protect the surface of the photocells against possible damage, including scratches, as this reduces the amount of light that reaches the 
photocells and therefore the output current.
The temperature of the transported air should be in the range from -15 ˚С to +40 ˚С.
The unit is rated as a Class III electrical appliance. 
Ingress protection rating against access to hazardous parts and water ingress is IP24.
The ventilator design is constantly being improved, thus some models may be slightly different from those described in this manual.

The dimensions of the ventilator are shown below.

Voltage [V]

Current [A]

Impeller RPM [min-¹]

Air flow [m³/h]

9

0.064

1390

13

12

0.073

1754

15

15

0.083

2140

17

18

0.092

2490

20

Содержание SHM 100 DK













Отзывы: