Blastrac BMP-335 EHY Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 40

Blastrac BMP-335 EHY Скачать руководство пользователя страница 32

32

6.4

Lubrication

The observance of our lubrication instructions will protect against
premature maintenance and repair work on the machine.

Dirt and foreign bodies could considerably reduce the working life of the
bearings or other moving parts of the machine. Therefore the lubrication
points must be cleaned thoroughly before lubricating.

Lubrication and all required work has to be done while the machine is
disconnected from the power supply, and in its safety off position.



Check the oil level in the hydraulic reservoir.
(E00481 Hydraulic oil HV-46)



Check the hand wheel depth adjustment for smooth running.



Lubricate the 2 nipples under the hand wheel for depth
adjustment.

Disassemble the drive wheel (2) by loosening the bolt
(1).

Remove chain guard (4) by loosening the bolt (3).

Apply oil only in this section and clean up all parts in
order to remove excessive oil.

Regularly check the correct tension of the chain. Adjust
the tension by loosening the bolts (6), turn hydraulic
motor clockwise and tighten the bolts again.

Apply oil behind felt seal (5) when it is hard to move
the machine around in free-wheel position.

«
...
30
31
32
33
34
...
»

Содержание BMP-335 EHY









































Отзывы:

Нет отзывов