Blastrac 1-16DB4-V2 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 62

Blastrac 1-16DB4-V2 Скачать руководство пользователя страница 17

Operation Adjustments

The 1-16DB4-V2 is equipped with a few fine tune adjustments to make blasting
easier.

1.

Front End Lift:

This is used primarily for loading and unloading the machine. This

feature may also be used to adjust your seals while operating the machine,
opposed to stopping the machine and doing it manually.

2.

Silencer Box:

This is used to adjust the amount of vacuum pulled through the blast

housing. It can be used to fine tune air flow to the specific application.

3.

Pinch Bar:

The pinch bar clearance must be checked before each operation. For

best blasting results, adjust the pinch bar 1/8-inch clearance for all applications.

4.

Dampener Plates:

This feature allows you to adjust the blast pattern if needing a

thinner blast width such as in line stripe removal or other special applications.

17

After Adjusting the pinch bar to blade gap, always spin the blast wheel to
verify clearance on all blades.

«
...
15
16
17
18
19
...
»

Содержание 1-16DB4-V2































































Отзывы:

Нет отзывов