background image

3

EN

•  Always keep a safe distance in all directions 

around your model to avoid collisions or injury. This 
model is controlled by a radio signal subject to in-
terference from many sources outside your control. 
Interference can cause momentary loss of control.

•  Always operate your model in open spaces away 

from full-size vehicles, traffi c and people.

•  Always carefully follow the directions and warnings 

for this and any optional support equipment 
(chargers, rechargeable battery packs, etc.).

•  Always keep all chemicals, small parts and any-

thing electrical out of the reach of children.

•  Always avoid water exposure to all equipment 

not specifi cally designed and protected for this 
purpose. Moisture causes damage to electronics.

•  Never place any portion of the model in your mouth 

as it could cause serious injury or even death.

•  Never operate your model with low transmitter 

batteries.

•  Always keep the aircraft in sight and under control.
•  Always move the throttle fully down at rotor strike.
•  Always use fully charged batteries.
•  Always keep the transmitter powered on while the 

aircraft is powered.

•  Always remove batteries before disassembly
•  Always keep moving parts clean.
•  Always keep parts dry.
•  Always let parts cool after use before touching.
•  Always remove batteries after use.
•  Never operate an aircraft with damaged wiring.
•  Never touch moving parts.

Safety Precautions and Warnings

Содержание GB200

















Отзывы: