Black Widow Security 953 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 12

Black Widow Security 953 Скачать руководство пользователя страница 2

Armed output: Orange wire will pro-
duce a grounded output when system is
armed.
Flashing Parking Light Output:
Armed: 1 second pulsed, Disarmed: 2-one
second pulses-, then output will latch on
for 30 seconds, or until ignition is turned
on, or system rearms. System triggered: 1
second pulse on, 1 second off, repeated
for 45 seconds.
Dome Light Output: Output is identi-
cal to Flashing Parking Light Output.

Super Selective
Receiver Board:

The new receiver design allows for a
much narrower band width reception. It
rejects RF interference that causes incon-
sistent range in similar type products and
improves the range of transmission
between remote and receiver. Average
minimum range is 100’ although it is com-
mon to get between 150’-300’. Our
extended range model with windshield
mounted receiver allows for up to 500’ of
range.

3 CHANNEL SOFTWARE
UPDATE

All 3 channel platforms have been updated
with new programmable features!
Features that can be programmed are the
following:
1. Parking lights can be programmed to

not stay on after disarm (car locator func-
tion).
2. Double unlock pulses can be added.
3.The 3rd channel can be programmed to
give a pulsing output when alarm is trig-
gered to be connected to the car horn.
4. 2nd channel Auto disarm feature, when
the 2nd channel is used for opening the
trunk or hatch, the alarm (if armed) will
automatically disarm.

To program these specific features
follow the procedure below:
1.Turn ignition key to the ON position
2. Press the valet switch 5 times.
3.Then select the program that you wish
to change and press the valet switch the
same number of times.
4. Press button one or two on the trans-
mitter to change to the desired program
to the feature.
Example: Programming the 3rd channel to
horn output.
1. Ignition Key On,
2. Press Valet switch 5 times
4. Next, press Valet switch 3 times.
5. Press button #2 on transmitter
6.Turn ignition key off.The red/white wire on
the main harness now is programmed to be
a horn output when the alarm is triggered or
panicked.

Using Valet/Override Switch

Valet Mode: If the system is pro-
grammed to passively arm (dip switch #4

2

«
1
2
3
4
...
»

Содержание 953













Отзывы:

Нет отзывов