Black Horce Model PZL 104 Wilga Скачать руководство пользователя страница 1

Страница: 1 / 16

Made in Vietnam.

Instruction Manual Book

Item code: BH156.

95% ALMOST READY TO FLY

PZL 104 Wilga

- Wingspan: 1,720mm (67.72 in).
- Length: 1,320 mm (51.97 in).
- Weight: 3.9 kg (8.58 lbs).
- Wing area: 41dm

- Wing loading: 95.12g/dm

- Wing type: Naca Airfoil.
- Gear type: Aluminium Hi-grade
and oleo struts for main gear (included).
- Servo mount: 42mm x 21mm.

SPECIFICATION

Parts listing required (not included):

- Radio: 05 channels.
- Servo: 07 servos.
- Engine: 61 - 2 stroke; 15cc Gas.
- Motor: Brushless outrunner 1200-2200W, 650KV.
- Propeller: Suit with your engine.

Recommended motor

and battery set up (not included):

- Motor: RIMFIRE.60.
- Lipo cell: 6 cells 4,000-5,000mAh.
- Receiver battery: 6V/ 1200-2000mAh NiMH.
- ESC: 80A.

ALL BALSA - PLY WOOD CONSTRUCTION.

COVERED WITH ORACOVER

Содержание PZL 104 Wilga

















Результаты поиска

Содержание PZL 104 Wilga

Отзывы:

Похожие инструкции для PZL 104 Wilga

Бренды по названию

Популярные бренды

Black Horce Model PZL 104 Wilga, Инструкция по эксплуатации

Результаты поиска

Содержание PZL 104 Wilga

Отзывы:

Похожие инструкции для PZL 104 Wilga

Бренды по названию

Популярные бренды