background image

EDGE 540-V3 30cc             Item code: BH94

.                      

Instruction Manual

7

5mm

Bend as shown

here.

Atter confirming the 

direction (see front 

view of fuel tank).

insert and tighten 

the screw.

Vent tube

Fuel pick - up tube

Fuel fill tube

Tygon gas tubing

not included.

   

5)   

Test  fit  the  stopper  assembly  into  the 

tank. It may be necessary to remove some of the  

flashing  around  the  tank  opening  using  a  

modeling knife.  If flashing  is  present,  make sure 

none of it falls into the tank.

  

6)  

When satisfied with the alignment of the 

stopper  assembly  tighten  the  3mm  x  20mm  

machine screw until the rubber stopper expands 

and seals the tank opening. Do not over tighten 

the assembly as this could cause the tank to split.

  

7)  

Using a modeling knife, cut 3 lengths of 

fuel  line  150mm  long.  Connect  2  lines  to  the  2 

vent tubes and 1 line to the fuel pickup tube in the 

stopper.

   

8)   

Feed  three  lines  through  the  fuel  tank

compartment and through the pre-drilled hole in the 

firewall. Pull the lines out from behind the engine, 

while guiding the fuel tank into place. Push the fuel 

tank as far forward as possible, the front of the tank 

should just about touch the back of the firewall.

Blow through one of the lines to ensure the fuel 

lines have not become kinked inside the fuel tank 

compartment. Air should flow through easily.

Fuel tank

Pushrod wire

Pushrod choke

Install one adjustable metal connector through the 
third hole out from the center of one servo arm, 
enlarge the hole in the servo arm using a 2mm drill 
bit to accommodate the servo connector. Remove 
the excess material from the arm.

After installing the adjustable metal connector 

apply a small drop of thin C/A to the bottom nut. 

This will prevent the connector from loosening 

during flight.

2. INSTALLING THE THROTTLE - CABLE

  

9) 

To secure the fuel tank in place, apply a 

bead of silicon sealer to the forward area of the 

tank, where it exits the fuselage behind the engine 

mounting box and to the rear of the tank at the 

forward bulkhead.

Do  not  secure  the  tank  into  place  permanently 

until after balancing the airplane. You may need 

to remove the tank to mount the battery in the fuel 

tank compartment.

Содержание EDGE-540-V3




















Отзывы: