background image

EDGE 540-V3 30cc             Item code: BH94

.                      

Instruction Manual

15

 

1)

  Cut out the switch hole using a modeling 

knife.  Use  a  2mm  drill  bit  and  drill  out  the  two 

mounting holes through the fuselage side.

 

2)

  Secure the switch in place using the two 

machine screws provided with the radio system.

 

1)

  Plug the servo leads and the switch lead 

into the receiver. You may want to plug an aileron 

extension into the receiver to make plugging in the 

aileron servo lead easier when you are installing 

the wing. Plug the battery pack lead into the switch.

 

2)

   Wrap the receiver and battery pack in the 

protective  foam  to  protect  them  from  vibration. 

Use a rubber band or masking tape to hold the 

foam in place.

 

3) 

 Position the battery pack and receiver behind 

the fuel tank. Use  two tie wraps to hold the battery 

and receiver securely in place as pictures below.

Do not permanently secure the receiver and battery 

until after balancing the model. 

 

4)

  Using a 2mm drill bit, drill a hole through 

the side of the fuselage, near the receiver, for the 

antenna to exit.

XIII. INSTALLING THE RECEIVER 

AND BATTERY

Switch of engine

Battery of engine

Battery receiver

Receiver

Remove covering.

C/A glue.

XII. INSTALLING THE SWITCH

C/A Epoxy.

Содержание EDGE-540-V3




















Отзывы: