Black+Decker BCASK8967D2, Оригинальное руководство пользователя

Страница: 24 / 208

24
ENGLISH (Original instructions)
25
ENGLISH (Original instructions)
u
Do not allow spool cap to drag on ground or
other surfaces.
u
In long growth, cut from the top down and do not exceed
304.8 mm high.
u
Keep trimmer tilted toward the area being cut; this is the
best cutting method.
u
The trimmer cuts when passing the unit from the left to
right. This will avoid throwing debris at the operator.
u
Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by the string.
Accessories
Compatible with CM100 mower base sold seperately.
Replacing the spool (fig.D9, D10, D11, D12, D13)
Warning! To reduce the risk of serious personal injury, turn
unit off and remove the battery pack before making any ad-
justments or removing/installing attachments or accessories.
An accidental start-up can cause injury.
u
Depress the spool cap release tabs (28) and remove the
spool cap (27) from the spool housing (26) in the trimmer
head (fig. D9).
u
Grasp empty spool with one hand and spool housing with
other hand and pull spool out.
u
If lever (26b) (fig. D10) in base of housing becomes
dislodged, replace in correct position before inserting new
spool into housing.
u
Remove any dirt and grass from the spool and housing.
u
Unfasten the end of the cutting line Fig. D11 and guide the
line into the eyelet (26c) Fig. D12.
u
Take the new spool and push it onto the boss (26a) in
the housing (Fig. D10). Rotate the spool slightly until it is
seated. The line should protrude approximately 136mm
from the housing.
u
Align the tabs on the spool cap with the slots in the
housing (Fig. D13).
u
Push the cap onto the housing until it snaps securely
into place.
Rewinding spool from bulk line (fig. D14, D15, D16)
Bulk line is also available for purchase from your local retailer.
Note: Hand wound spools from bulk line are likely to
become tangled more frequently than BLACK+DECKER
factory wound spools. For best results, factory wound spools
are recommended.
To install bulk line, follow the steps below:
u
Remove battery pack from trimmer.
u
Remove the empty spool from the trimmer as described in
“REPLACING THE SPOOL”.
u
Remove any remaining cutting line from the spool.
u
Make a fold at the end of the cutting line at about 19mm
(26d). Feed the cutting line into one of the line anchoring
slots (26e) as shown in Fig. D14.
u
Wind the cutting line onto the spool in the direction of the
arrow on the spool. Make sure to wind the line on neatly
and in layers. Do not crisscross (Fig. D16).
u
When the wound cutting line (26g) reaches the recesses
(26f), cut the line. (Fig. D15).
u
Fit the spool onto the trimmer as described in
“REPLACING THE SPOOL”.
Troubleshooting
Problem Possible Cause Possible Solution
Unit will not
start.
Battery pack not installed
properly.
Battery pack not charged.
Internal componets too hot.
Attachment or extension pole
not attached to the base unit.
Check battery pack
installation
Check battery pack
charging requirements.
Allow tool to cool down.
Ensure attachemnt is
properly seated and locked
into position on the
extension pole.
Ensure extension pole is
properly seated and locked
into position on the base
unit.
Battery pack
will not
charge.
Battery pack not inserted into
charger.
Charger not plugged in.
Surrounding air temperature
too hot or too cold
Insert battery pack into
charger until LED
illuminates.
Plug charger into a working
outlet. Refer to "Important
charging notes" for more
details.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (4,5°C) or below
105 degrees F (+40,5°C)
Unit shuts off
abruptly.
Battery pack has reached its
maximum thermal limit.
Out of charge. (To maximize
the life of the battery pack it is
designed to shut off abruptly
when the charge is depleted.)
Allow battery pack to cool
down.
Place on charger and allow
to charge.
Maintenance
Your BLACK+DECKER appliance has been designed
to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper care and regular cleaning.
u
Regularly clean the appliance using a damp cloth. Do not
use any abrasive or solvent-based cleaner. Never let any
liquid get inside the appliance and never immerse any part
of the appliance into liquid.
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.