Black Box MT136A Скачать руководство пользователя страница 93

Страница: 93 / 116

CSU/DSU MS DBU

Appendix A. Pinouts

The following tables give the pin assignments for the connectors on the back
of the CSU/DSU MS DBU, the DBU cards, and the SNMP Ethernet Module.
For more information on the connectors, see Chapter 2.

Table A-1. Pin Assignments for Telco Connector

Pin

Name

Description

Transmit Data from DSU to Network—Ring 1

Transmit Data from DSU to Network—Tip 1

3-6

—

Not Used

Receive Data from Network to DSU—Tip

Receive Data from Network to DSU—Ring

Table A-2. Pin Assignments for DBU Card Connectors

Pin

Name

Description

4-wire Switched 56

Transmit Data from DSU to Network—Ring 1

Transmit Data from DSU to Network—Tip 1

3-6

—

Not Used

Receive Data from Network to DSU—Tip

Receive Data from Network to DSU—Ring

V.34 and 1B+D ISDN

1-3

—

Not Used

Network—Tip

Network—Ring

6-8

—

Not Used

Содержание MT136A




















































































































Результаты поиска

Содержание MT136A

Отзывы:

Black Box MT136A, Руководство пользователя, Страница: 93 / 116

Результаты поиска

Содержание MT136A

Отзывы: