manualshive.com logo in svg

Black Box MT136A, Руководство пользователя, Страница: 8 / 116

Поделиться
Скачать
Black Box MT136A Скачать руководство пользователя страница 8

7

FCC REGULATIONS

FCC regulations require that the following information be provided in this
manual:

1. This equipment complies with Part 68 of the FCC rules. On the bottom of

the equipment housing is a label that shows the FCC registration number
and ringer equivalence number (REN) for this equipment. If requested,
provide this information to the telephone company.

2. If this equipment causes harm to the telephone network, the telephone

company may temporarily discontinue service. If possible, advance notification
is given; otherwise, notification is given as soon as possible. The telephone
company will advise the customer of the right to file a complaint with the FCC.

3. The telephone company may make changes in its facilities, equipment,

operations, or procedures that could affect the proper operation of this
equipment; advance notification and the opportunity to maintain
uninterrupted service are given. 

4. If experiencing difficulty with this equipment, please contact Black Box

for repair and warranty information. The telephone company may require
this equipment to be disconnected from the network until the problem is
corrected, or it is certain the equipment is not malfunctioning.

5. This unit contains no user-serviceable parts.

6. An FCC-compliant telephone cord with a modular plug is provided with this

equipment. In addition, an FCC-compliant cable appropriate for the dial-
backup option ordered is provided with this equipment. This equipment
is designed to be connected to the telephone network or premises wiring
using an FCC-compatible modular jack that is Part 68 compliant.

7. The following information may be required when applying to the local

telephone company for leased-line facilities:

Digital Facility

Service Order

Service Type

Interface Code

Code

Network Jacks

2.4 kbps Digital Interface

04DU5-24

6.0F

RJ-48S

4.8 kbps Digital Interface

04DU5-48

6.0F

RJ-48S

9.6 kbps Digital Interface

04DU5-96

6.0F

RJ-48S

19.2 kbps Digital Interface

04DU5-19

6.0F

RJ-48S

38.4 kbps Digital Interface

04DU5-38

6.0F

RJ-48S

56 kbps Digital Interface

04DU5-56

6.0F

RJ-48S

64 kbps Digital Interface

04DU5-64

6.0F

RJ-48S

Содержание MT136A





















































































































Отзывы:

Нет отзывов