manualshive.com logo in svg

Black Box MT136A, Руководство пользователя, Страница: 78 / 116

Поделиться
Скачать
Black Box MT136A Скачать руководство пользователя страница 78

77

CHAPTER 12: Testing and Troubleshooting

remote unit is error free. Run the test using all available test patterns.

NOTE

If an external BERT tester is available, these additional tests may be
performed:

•

DTE & Loop Test

•

DTE Only Test

•

Loop Only Test

If the unit fails any of these tests or the problem has not been determined, contact
Black Box.

12.3 Local Unit Diagnostics

The local CSU/DSU MS DBU can perform six different tests; see Table 12-3.

Table 12-3. Test AT Commands

Front-Panel Display

AT Command

Description

DTE & Loop (LL)

&T10

TD/RD and RX/TX Loopbacks

Loop Only (RT)

&T11

RX/TX Loopback at Network Interface

DTE Only

&T1

TX/RX Loopback at DTE Interface

DTE with TP

&T8

TX/RX Loopback with Test Pattern

Test Pattern

&T9

Transmit/Receive Test Pattern

Self Test

Z

Check Internal Components (Resets Unit)

Exit Test

&T0

Stops test, returns to data mode

TD = Customer Transmit Data
RD = Customer Receive Data
TX = Network Transmit Data
RX = Network Receive Data

The test patterns shown in Table 12-4 are available for the DTE with Test Pattern
and Test Pattern tests.

Содержание MT136A





















































































































Отзывы:

Нет отзывов