Black Box MT136A Скачать руководство пользователя страница 12

Страница: 12 / 116

CONTENTS

Contents

Chapter

Page

1. Introduction........................................................................................................15

1.1 Overview ....................................................................................................15

1.2 DDS Operation ........................................................................................16

1.3 Switched 56 Operation ............................................................................16

1.4 SNMP ........................................................................................................16

1.5 TELNET ....................................................................................................17

1.6 Dial-Backup Operation ............................................................................17

1.7 Dial Backup Modes ..................................................................................17

2. Installation ..........................................................................................................19

2.1 Unpack, Inspect, and Power Up ..............................................................19

2.2 Rear Panel ................................................................................................20

3. Operation ............................................................................................................24

4. Applications ........................................................................................................30

4.1 LAN Application with SNMP/TELNET Management ..........................30

4.2 Dial-Backup Application ..........................................................................33

5. Configuration Overview ....................................................................................36

6. Configuring Network Options ..........................................................................42

6.1 Loop Rate ..................................................................................................43

6.2 Network Address ......................................................................................43

6.3 Remote Configuration..............................................................................44

6.4 Network Type ............................................................................................44

6.5 Clock Source ............................................................................................44

7. Configuring DTE Options ................................................................................45

7.1 DTE Rate ..................................................................................................48

7.2 Connector Type ........................................................................................48

7.3 Data Format ..............................................................................................48

7.4 DTE Command Option............................................................................49

Содержание MT136A




















































































































Результаты поиска

Содержание MT136A

Отзывы:

Black Box MT136A, Руководство пользователя, Страница: 12 / 116

Результаты поиска

Содержание MT136A

Отзывы: