Black Box LB522A-KIT Скачать руководство пользователя страница 21

Страница: 21 / 112

724-746-5500 | blackbox.com

Page 21

Hardware Installation

NOTE: Power cables are shipped separately from the LB52xA-KIT

3.1.6 Connecting cables

1. Connect the Ethernet cable to the Management port. LB52xA-KIT supports audi-

MDIX switching so you may use a crossover or straight-through cable.

2. Connect one end of a phone cable to the LINE port and the other end of the cable

to a wall jack.

3.1.7 Grounding the LB52xA-KIT and connecting power

When connecting to the power source, it is important to establish a good grounding
connection first, and then the power connection. Do the following:

1. Assemble a ground wire using #10 AWG wire with green-colored insulation and

two ring terminals. Make the wire long enough to reach one of the following earth

ground sources:

• The building ground rod (generally located at the site’s main service entrance)

• A sprinkler system pipe

• A cold-water pipe

• Building structural steel

The Interconnecting cables must be acceptable for external use
and must be rated for the proper application with respect to volt-
age, current, anticipated temperature, flammability, and mechani-
cal serviceability.

Do not work on the system or connect or disconnect cables during
periods of lightning activity.

CAUTION

WARNING

Содержание LB522A-KIT

















































































































Результаты поиска

Содержание LB522A-KIT

Отзывы:

Похожие инструкции для LB522A-KIT

Бренды по названию

Популярные бренды

Black Box LB522A-KIT, Руководство пользователя

Результаты поиска

Содержание LB522A-KIT

Отзывы:

Похожие инструкции для LB522A-KIT

Бренды по названию

Популярные бренды