Black & Decker Scumbuster, Руководство по эксплуатации

Страница: 6 / 12

6
4. Scrub pad & disc
5. Liquid reservoir
6. Charger connector
Accessories (fig. A)
This product is supplied with the following accessories:
7. Wide area bristle brush: for aggressive area cleaning on
ceramic tile walls and floors, fibreglass and hard plastic
surfaces
8. Pad disc: for use with pads
9. Mild scrub pad (white): for milder scrubbing of large areas,
such as ceramic tile walls and floors or outdoor furniture
10. Coarse scrub pad (light blue): for aggressive scrubbing of
larger surfaces, such as ceramic tile walls and floors or
bath tubs and sinks (porcelain or enamel)
11. Heavy scrub pad (green): for aggressive scrubbing on
large surfaces, such as barbecue grill grates
12. Radial brush: for tile grout cleaning
13. Narrow brush: for cleaning of corners and hard to reach
places
14. Carpet brush: for carpet cleaning
15. Flexible attachment: for use of brushes and scrub pads in
curved places
16. Carrying caddy: for portable and convenient storage of the
unit and accessories
17. Wall mount: for storage of the unit during charging
18. Cleaning stick: for unclogging of the dispensing system
Installation
Mounting the wall mount to the wall (fig. B)
The wall mount can be fitted to the wall to provide a
convenient storage and charging point for the appliance.
◆
Locate the wall mount (17) within reach of a mains supply.
Fit the wall mount using the appropriate hardware.
◆
Plug in the charger.
◆
Insert the cord of the charger into the groove (19) in the
bottom of the wall mount. Allow sufficient length of cord
to connect the charger plug (20) to the appliance when
placed in the wall mount.
Warning! Do not fit the wall mount directly over a mains
supply. Ensure the cord has a loop when the charger is
connected to the mains.
Assembly
Warning! Before assembly, switch off the tool.
Fitting and removing an accessory (fig. C)
Fitting
◆
When using a pad, fit the pad onto the pad disc.
◆
Align the triangular notch on the accessory with the shaft
on the motor unit.
◆
Place the accessory onto the shaft. Snap and twist the
accessory quickly in the clockwise direction.
Removing
◆
Snap and twist the accessory quickly in the
counterclockwise direction and pull it off the motor unit.
Fitting flexible attachment (fig. D)
The flexible attachment (15) must be fitted between the motor
unit and the accessory.
◆
Fit the flexible attachment onto the appliance as
described above.
◆
Fit the accessory onto the appliance flexible attachment.
Warning! Never use the flexible attachment without a brush
or scrub pad in place. Do not use the flexible attachment for
carpet cleaning.
Use
◆
Before first use, the battery must be charged for at least
16 hours.
◆
Place the appliance in the wall mount whenever it is not
in use.
◆
Leave the appliance connected to the charger whenever it
is not in use.
Charging the battery (fig. E)
◆
Before charging, make sure that the appliance is switched
off.
◆
Place the appliance in the wall mount (17) as shown.
◆
Insert the charger plug (20) into the charger connector (6)
at the rear of the appliance.
◆
Plug in the charger. Switch on at the mains.
The indicator light on the charger will be lit and will stay lit as
long as the battery is connected to the charger.
◆
Leave the appliance to charge for at least 16 hours.
Whilst charging, the charger may become warm. This is normal
and does not indicate a problem. The appliance can be left
connected to the charger indefinitely.
◆
After disconnecting the appliance from the charger,
replace the charging plug.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C.