EN
G
LI
SH
ENGLISH
PRELIMINARY STEPS
4
5
Thank you for purchasing this Price Pfister product. All Price Pfister
products are carefully engineered, and factory tested to provide long
trouble-free use under normal conditions. This product is easy to
install using basic tools and our easy to follow illustrated instructions.
If you have any questions regarding this product, call 1-800-Pfaucet
(1-800-732-8238).
1 BEFORE PROCEEDING
WARNING:
Read all the instructions completely before proceeding. Price Pfister
recommends calling a professional if you are uncertain about installing this product!
This product has been designed for use with the Price Pfister 0X6-440R
Roman Tub series rough-in. It will not work with any other product.
This product should be installed in accordance with all local and state plumbing and
building codes. For optimum performance of your new Price Pfister faucet, a minimum
water pressure of
25 PSI (172 kPa)
is recommended.
Your installation will require supply tubes. To preserve the high flow characteristics of
these valves, it is necessary to use ½” I.D. (⅝” O.D.) Copper tubing or Price Pfister
Quick Connect Hose Kit
15-136R
. Consult the store where you purchased your faucet
for the recommended connections that you may require for your area.
If Deck Thickness Exceeds 1
3
/
8
” (35 mm), Price Pfister Stem Extension Kit
974-375 must be used.
2 SHUT OFF WATER SUPPLY
Locate water supply inlets and shut off the water supply valves. These are usually
found near the water meter. If you are replacing an existing faucet, remove the faucet
from the tub and clean the tub surface thoroughly.
3 TOOLS RECOMMENDED:
● PTFE Plumber’s Tape or Thread Sealant
● Phillips Screwdriver
● Adjustable Wrench
● Hacksaw
● Flashlight
● Cloth
Your installation may require new supply lines and/or shut-off valves or other additional
tools.
4 IMPORTANT DIMENSIONS
Note:
Price Pfister recommends that all holes be 1
1
/
4
” (32 mm) diameter.
A) For Thick Wall:
Deck thickness must be between 1
3
/
8
” (35 mm) to 3” (76 mm) max.
Verify that the top of Outlet Tube (
4A
) is 1” (25.4 mm) above mounting surface as
shown. Use Installation Tool
931-054
to adjust (refer to 0X6 Installation Instructions).
Price Pfister Stem Extension Kit
974-375
must be used (
order separately
).
B) For Thin Wall:
Verify that the top of Stem (
4B
) is 1
5
/
8
” (41 mm) above mounting
surface as shown. Deck thickness must not exceed 1
3
/
8
” (35 mm).
For Thin Wall Installation Go To Step 8
For Thick Wall Installation Go To Step 6
5 STEM ROTATION SET UP
Stem Stop (
5A
) can be inserted into Stem (
5C
) in either of two ways, depending on the
rotation you want to have for your handles. When removing and/or installing Stem Stop
(
5A
), you must look for Missing Tooth (
5B
) on both Stems (
5C
) and Stem Stop (
5A
), and
align them. If you want both handles rotating in the same direction, you must be able
to see Groove (
5D
) on the stop on both Stems when installed (
As shown in
B
).
If you
want the handles rotating in opposite directions, you will see Groove (
5D
) on only one
of the stems when installed (
As shown in
A
).
2
1”
(25.4 mm)
3”
(76 mm) Max.
1
5
/
8
”
(41 mm)
1
3
/
8
”
(35 mm) Max.
4B
4A
A
THICK WALL INSTALLATION
THIN WALL INSTALLATION
B
5A
5A
5C
5C
5A
5A
5C
5C
5D
5D
5D
5D
5B
5B
5B
5B
A
B
HOT
HOT
COLD
COLD