background image

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on
another tool.

SERVICE

Tool service must be performed only by qualified repair personnel.

Service or

maintenance performed by unqualified personnel could result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instructions in the
Maintenance section of this manual.

Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES

Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord.

Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:

•    lead from lead-based paints,
•    crystalline silica from bricks and cement and other masonry products, and 
•    arsenic and chromium from chemically-treated lumber. (CCA)

Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals:  work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. 

Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: 

Use of this tool can generate and/or disburse dust, which may cause serious

and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

The label on your tool may include the following symbols.

V ..........................volts

A..........................amperes

Hz ........................hertz

W ........................watts

min ........................minutes

......................alternating current

......................direct current

no ........................no load speed

..........................Class II Construction

........................

earthing terminal

........................safety alert symbol

.../min ..................revolutions or 

reciprocations
per minute

First Aid Measures for Gel Components (DR220G Only)

If gel within the comfort grip becomes exposed and results in skin contact wash with soap
and water; for eye contact, flush with flowing water. If swallowed, seek medical attention.
Material Safety Data Sheet (MSDS) available from 

1-800-544-6986.

SAFETY WARNINGS AND INSTRUCTIONS: DRILLS

When drilling or driving into walls, floors or wherever live electrical wires may be
encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only
by the plastic handle(s) to prevent shock. 

• Do not lock the tool ON when drilling by hand. Refer to Operating Instructions-Switch.

Hold drill firmly to control the twisting action of the drill. If your drill is equipped with a
side handle, always use the side handle. 

General Safety Rules

WARNING:

Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

Keep your work area clean and well lit.

Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust or

fumes.

Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

Double insulated tools are equipped with a polarized plug (one blade is wider than the
other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install a polarized outlet. Do not change the plug in any way.

Double insulation 

eliminates the need for the three wire grounded power cord and grounded power supply
system.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators.

There is an increased risk of electric shock if your body is grounded.

Don’t expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged
cords immediately.

Damaged cords increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked "W-A"
or "W." 

These cords are rated for outdoor use and reduce the risk of electric shock. 

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. 

A moment of inattention while operating power tools may result in serious

personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. 

Loose clothing, jewelry, or long hair

can be caught in moving parts.  Air vents cover moving parts and should be avoided.

Avoid accidental starting. Be sure switch is off before plugging in. 

Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

Remove adjusting keys or wrenches before turning the tool on.

A wrench or key that is

left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.

Proper footing and

balance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

Use clamps or other practical way to secure and support the workpiece to a stable
platform. 

Holding the work by hand or against your body is unstable and may lead to loss

of control.

Do not force tool. Use the correct tool for your application.

The correct tool will do the

job better and safer at the rate for which it is designed.

Do not use tool if switch does not turn it on or off.

Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the tool. 

Such preventative safety measures reduce

the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. 

Tools are

dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean. 

Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tools operation. If damaged, have the tool serviced
before using.

Many accidents are caused by poorly maintained tools.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. 

ADVERTENCIA: 

LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO. 

Catalog #’s DR201, DR202, DR211, DR220, DR220G, DR403, DR501, DR601
Form No. 630167-00   (JAN. 05)      Copyright © 2005 Black & Decker          

Printed in China

Hammering position
Position de martelage
Posición de martillar 

Drilling position
Position de perçage
Posición de taladrar 

Lever

Levier

Palanca

CATALOG NUMBERS -

DR201, DR202, DR211, DR220,

DR220G, DR403, DR501, DR601

INSTRUCTION

MANUAL

3

3

3

3

//

//

8

8

8

8

"

"

"

"

  

  

((

((

1

1

1

1

0

0

0

0

m

m

m

m

m

m

m

m

))

))

  

  

a

a

a

a

n

n

n

n

d

d

d

d

  

  

1

1

1

1

//

//

2

2

2

2

"

"

"

"

  

  

((

((

1

1

1

1

3

3

3

3

m

m

m

m

m

m

m

m

))

))

  

  

D

D

D

D

rr

rr

ii

ii

ll

ll

ll

ll

s

s

s

s

  

  

a

a

a

a

n

n

n

n

d

d

d

d

  

  

H

H

H

H

a

a

a

a

m

m

m

m

m

m

m

m

e

e

e

e

rr

rr

  

  

D

D

D

D

rr

rr

ii

ii

ll

ll

ll

ll

s

s

s

s

BEFORE RETURNING THIS PRODUCT 

FOR ANY REASON PLEASE CALL 

1-800-544-6986

IF YOU SHOULD EXPERIENCE A PROBLEM 

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-544-6986

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No.,

AND DATE CODE (e.g. 200205-47). IN MOSTCASES, A

BLACK & DECKER 

REPRESENTATIVE CAN

RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGESTION OR COMMENT, GIVE

US ACALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.

Switch Control Lever
Bouton de commande de l'in-
terrupteur 
Palanca de control de inversión

Lock-on button

Bouton de verrouillage en position de marche 

Botón de cierre para funcionamiento continuo 

3

1

2

Trigger Switch
Interrupteur à gâchette
Interruptor de disparo

Hammering position
Position de martelage
Posición de martillar 

Drilling position
Position de perçage
Posición de taladra

Lever
Levier
Palanca

7A

7B

Model DR403
Modèle DR403
Modelo DR403

Model DR601
Modèle DR601
Modelo DR601 

6

Accessory Bit Holder
Porte-mèche
Sujetador de acceso-
rio de broca

4

5

Содержание DR201







Отзывы: