BKT Elektronik ACBS Скачать руководство пользователя страница 87

Страница: 87 / 92

www.bkte.pl

BKT ACBS - installation and configuration manual of the access control system with RS485 bus interface

9.12

Adding user group

It is convenient to start adding users from creating a group of
users who will have the rights to open a defined group of doors.
Any user who belongs to such group will have the rights of this
group.



In the system tree view click with the right button on Access
Users and select Add Group.



Enter the name of user group.



Click OK

You must assign authorisations that were created during the door
configuration to just created group.



In the system tree view click with the right button on just
created user group and select Open



Click on Authorisations.



Click on Assign.

Содержание ACBS





























































































Результаты поиска

Содержание ACBS

Отзывы:

Похожие инструкции для ACBS

Бренды по названию

Популярные бренды

BKT Elektronik ACBS, Руководство по установке и настройке

Результаты поиска

Содержание ACBS

Отзывы:

Похожие инструкции для ACBS

Бренды по названию

Популярные бренды