BIXOLON SRP-330III страница 40 Скачать руководство пользователя

Страница: 40 / 116

SRP-330/332III

Rev. 1.00

BIXOLON

- 40 -

Remarks:

■

The horizontal and vertical starting positions are out of the printable area, this command is canceled and the following

data is processed as normal data.

■

If (Horizontal starting po Horizontal printing area width) is beyond the printable area, the Horizontal printing

area width is set to (Horizontal printing area - Horizontal starting position).

■

If (Vertical starting po Vertical printing area width) is beyond the printable area, the Vertical printing area width

is set to (Vertical printing area - Vertical starting position).

■

This command is not effective in standard mode. If this command is processed in standard mode, the setting by this

command is effective when the printer returns to page mode.

■

The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.

Differences:

The maximum printable area(Max horizontal printable area, Max vertical printable area):

Model

Max horizontal printable area

Max vertical printable area

SRP-330III

72.2mm(512dots)

234.3mm(1662dots)

SRP-332III

72mm(576dots)

207.75mm(1662dots)

Содержание SRP-330III





















































































































Результаты поиска

Содержание SRP-330III

Отзывы:

Похожие инструкции для SRP-330III

Бренды по названию

Популярные бренды

BIXOLON SRP-330III, Руководство по управлению

Результаты поиска

Содержание SRP-330III

Отзывы:

Похожие инструкции для SRP-330III

Бренды по названию

Популярные бренды