BIXOLON SRP-330II Скачать руководство пользователя

Страница: 49 / 125

SRP-330II/332II

Rev. 1.00

BIXOLON

- 49 -

ESC v

Function:

Transmit paper sensor status

Code:

ASCII

ESC

Hex

Decimal

118

Range:

None

Default:

None

Description:

■

This command transmits a byte of data specifying the paper sensor status.

■

The status of paper near end and paper end sensors is sent to the host as follows:

•

When paper near end is detected, 0x03 is transmitted.

•

When paper end is detected, 0xC is transmitted.

Remarks:

■

The paper sensor status can be transmitted using GS r.

■

The near end senor is optional while paper end sensor required.

■

If the printer is not equipped with a near end sensor, the paper near end sensor is considered as normal condition.

Differences:

None

Содержание SRP-330II






























































































































Результаты поиска

Содержание SRP-330II

Отзывы:

Похожие инструкции для SRP-330II

Бренды по названию

Популярные бренды

BIXOLON SRP-330II, Руководство по управлению

Результаты поиска

Содержание SRP-330II

Отзывы:

Похожие инструкции для SRP-330II

Бренды по названию

Популярные бренды